| 数据搜索系统,热门电子元器件搜索 |
|
STM32F412RGU6 数据表(PDF) 83 Page - STMicroelectronics |
|
|
|||||||||||||||||||||||||||||
STM32F412RGU6 数据表(HTML) 83 Page - STMicroelectronics |
|
83 / 201 page ![]() DocID028087 Rev 7 83/201 STM32F412xE/G Electrical characteristics 166 PD Power dissipation at TA = 85°C for range 6 or TA = 105°C for range 7(8) UFQFPN48 - - 625 mW WLCSP64 - - 392 LQFP64 - - 425 LQFP100 - - 465 LQFP144 - - 571 UFBGA100 - - 351 UFBGA144 - - 416 PD Power dissipation at TA = 125 °C for range 3(8) UFQFPN48 - - 156 WLCSP64 - - 98 LQFP64 - - 106 LQFP100 - - 116 LQFP144 - - 142 UFBGA100 - - 88 UFBGA144 - - 104 TA Ambient temperature for range 6 Maximum power dissipation -40 - 85 °C Low power dissipation(9) -40 - 105 Ambient temperature for range 7 Maximum power dissipation -40 - 105 Low power dissipation(9) -40 - 125 Ambient temperature for range 3 Maximum power dissipation -40 - 110 Low power dissipation(9) -40 - 130 TJ Junction temperature range Range 6 -40 - 105 Range 7 -40 - 125 Range 3 -40 - 130 1. VDD/VDDA minimum value of 1.7 V with the use of an external power supply supervisor (refer to Section 3.18.2: Internal reset OFF). 2. When the ADC is used, refer to Table 72: ADC characteristics. 3. If VREF+ pin is present, it must respect the following condition: VDDA-VREF+ < 1.2 V. 4. It is recommended to power VDD and VDDA from the same source. A maximum difference of 300 mV between VDD and VDDA can be tolerated during power-up and power-down operation. 5. Only the DM (PA11) and DP (PA12) pads are supplied through VDDUSB. For application where the VBUS (PA9) is directly connected to the chip, a minimum VDD supply of 2.7V is required. (some application examples are shown in appendix B) 6. Guaranteed by test in production 7. To sustain a voltage higher than VDD+0.3, the internal Pull-up and Pull-Down resistors must be disabled 8. If TA is lower, higher PD values are allowed as long as TJ does not exceed TJmax. 9. In low power dissipation state, TA can be extended to this range as long as TJ does not exceed TJmax. Table 16. General operating conditions (continued) Symbol Parameter Conditions Min Typ Max Unit |
|
链接网址 |
| ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 数据表链接 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |