ALUMINUM ELECTROLYTIC CAPACITORS

CAT.8100M

0.3 max.

C±0.2

H

H

0.3 max.

C±0.2

L±0.3

L±0.5

Series

Capacitance

Lot No.

Lot No.

Capacitance

Plastic platform

Plastic platform

Series

Trade mark

Voltage (C:16V)

Voltage (V:35V)

Negative

Positive

Negative

Positive

U

1

W

2

D

3

1

4

C

5

2

6

2

7

0

8

M

9

C

10

L

11

1

12

G

13

S

14

Configuration

Taping code

Capacitance tolerance (±20%)

Rated capacitance (22µF)

Rated voltage (16V)

Series name

Type

(mm)

A

B

C

E

L

H

4 × 5.8

1.8

4.3

4.3

1.0

5.8

0.5 to 0.8

5 × 5.8

2.1

5.3

5.3

1.3

5.8

0.5 to 0.8

6.3 × 5.8

2.4

6.6

6.6

2.2

5.8

0.5 to 0.8

6.3 × 7.7

2.4

6.6

6.6

2.2

7.7

0.5 to 0.8

8 × 10

2.9

8.3

8.3

3.1

10

0.8 to 1.1

10 × 10

3.2

10.3

10.3

4.5

10

0.8 to 1.1

φ D × L

UWD ChipType,LowImpedance

High Temperature (260°C) Reflow

Corresponding with 260°C peak reflow soldering

Recomended reflow condition : 260°C peak 5 sec. 230°C over 60 sec.

2 times (φ10 × 10 : 1 time)

Chip type, low impedance temperature range up to +105°C.

Designed for surface mounting on high density PC board.

Applicable to automatic mounting machine fed with carrier tape.

Compliant to the RoHS directive (2011/65/EU,(EU)2015/863).

AEC-Q200 Qualified. Please contact us for details.

Chip Type

Specifications

Category Temperature Range

Rated Voltage Range

Rated Capacitance Range

Capacitance Tolerance

Leakage Current

Tangent of loss angle (tan δ)

Stability at Low Temperature

Endurance

Shelf Life

Resistance to soldering

heat

Marking

Performance Characteristics

Item

–55 to +105°C

6.3 to 50V

1 to 1500µF

± 20% at 120Hz, 20°C

After 2 minutes' application of rated voltage at 20°C, leakage current is not more than 0.01 CV or 3 (µA), whichever is greater.

Black print on the case top.

The specifications listed at right shall be met

when the capacitors are restored to 20°C after the

rated voltage is applied for 5000 hours (2000

hours for

φD = 4, 5 and 6.3) at 105°C.

After storing the capacitors under no load at 105°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4

clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above.

Type numbering system (Example : 16V 22µF)

Measurement frequency : 120Hz at 20°C

Measurement frequency : 120Hz

(

) is φ8 over

Z(–25°C) / Z(+20°C)

Z(–55°C) / Z(+20°C)

Rated voltage (V)

Impedance ratio

ZT / Z20 (max.)

16

2

4

10

2

4

6.3

3

5

25

2

3

35

2

3

50

2

3

Rated voltage (V)

tan δ (max.)

50

0.12 (0.14)

35

0.12 (0.14)

25

0.14 (0.16)

16

0.16 (0.20)

10

0.20 (0.24)

6.3

0.26 (0.28)

Within ±30% of the initial capacitance value

Less than or equal to the initial specified value

200% or less than the initial specified value

Capacitance change

tan δ

Leakage current

Capacitance change

Leakage current

tan δ

Within ±10% of the initial capacitance value

Less than or equal to the initial specified value

Less than or equal to the initial specified value

The capacitors are kept on a hot plate for 30 seconds, which is

maintained at 250°C. The capacitors shall meet the characteristic

requirements listed at right when they are removed from the plate

and restored to 20°C.

(φ4 to φ6.3)

(φ8,φ10)

Dimension table in next page.

Voltage

V

6.3

10

16

25

35

50

Code

j

A

C

E

V

H

UWD

UUD

High

Temperature

Reflow

Frequency coefficient of rated ripple current

Coefficient

Frequency

50 Hz

120 Hz

300 Hz

1 kHz

10 kHz or more

0.35

0.50

0.64

0.83

1.00

※ I : Leakage Current (µA), C : Rated Capacitance (µF), V : Rated Voltage (V)