PI3CH1000LE datasheet(2/8 Pages) PERICOM

2 / 8 page

PS2724B

05/09/06

PI3CH1000

Low Voltage, 5-Ohm, 10-Channel

2-Port NanoSwitch™

Storage Temperature ................................................ –65°C to +150°C

Ambient Temperature with Power Applied ............... –40°C to +85°C

Supply Voltage to Ground Potential ........................... –0.5V to +4.6V

DC Input Voltage ........................................................ –0.5V to +6.0V

DC Output Current................................................................... 120mA

Power Dissipation ....................................................................... 0.5W

Note:

Stresses greater than those listed under MAXIMUM

RATINGS may cause permanent damage to the device. This is a

stress rating only and functional operation of the device at these

or any other conditions above those indicated in the operational

sections of this specification is not implied. Exposure to absolute

maximum rating conditions for extended periods may affect re-

liability.

Maximum Ratings

(Above which the useful life may be impaired. For user guidelines, not tested.)

DC Electrical Characteristics, 3.3V Supply (Over Operating Range, TA = –40°C to +85°C, VCC = 3.3V ± 10%)

Parameters

Description

Test Conditions(1)

Min.

Typ.(2) Max. Units

VIH

Input HIGH Voltage

Guaranteed Logic HIGH Level

VIL

Input LOW Voltage

Guaranteed Logic LOW Level

–0.5

0.8

VIK

Clamp diode Voltage

VCC = Min., IIN = –18mA

–1.3

–1.8

IIH

Input HIGH Current

VCC = Max., VIN = VCC

±1

µA

IIL

Input LOW Current

VCC = Max., VIN = GND

±1

IOZH

High-Impedence Current

0 ≤ A, B ≤ VCC

±1

RON

Switch On-Resistance(3)

VCC = Min.,VIN = 0V,

ION = –48mA or –64mA

Ω

VCC = Min., VIN = 3.6V, ION = –15mA

DC Electrical Characteristics, 2.5V Supply (Over Operating Range, TA = –40°C to +85°C, VCC = 2.5V ± 10%)

Parameters

Description

Test Conditions(1)

Min. Typ.(2)

Max.

Units

VIH

Input HIGH Voltage

Guaranteed Logic HIGH Level

1.8

VCC + 0.3

VIL

Inout LOW Voltage

Guaranteed Logic LOW Level

–0.3

0.8

VIK

Clamp Diode Voltage

VCC = Max., IIN = –6mA

–0.7

–1.8

IIH

Input HIGH Current

VCC = Max., VIN = VCC

±1

µA

IIL

Input LOW Current

VCC = Max., VIN = GND

±1

IOZH

High Impedance Current

0 ≤ A, B ≤ VCC

±1

RON

Switch On-Resistance(3)

VCC = Min., VIN = 0V,

ION = –48mA

Ω

VCC = Min., VIN = 2.25V,

ION = –15mA

Notes:

1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type.

2. Typical values are at VCC = 3.3V, TA = 25°C ambient and maximum loading.

3. Measured by the voltage drop between A and B pin at indicated current through the switch. On-Resistance is determined

by the lower of the voltages on the two (A,B) pins.

Notes:

1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type.

2. Typical values are at VCC = 3.3V, TA = 25°C ambient and maximum loading.

3. Measured by the voltage drop between A and B pin at indicated current through the switch. On-Resistance is determined

by the lower of the voltages on the two (A,B) pins.

06-0235

PI3CH1000LE 数据表(PDF) 2 Page - Pericom Semiconductor Corporation

PI3CH1000LE 数据表(HTML) 2 Page - Pericom Semiconductor Corporation

Html Pages

1 2 3 4 5 6 7 8

数据表下载