PA Pneuflex

N/UK 9.12.003.02

10/96

Our policy is one of continuous research and development. We therefore reserve the

right to amend, without notice, the specifications given in this document.

General Information – PA Pneuflex Spring Coils

Product number

O/D tube

I/D tube

A

B

Length of closed

Length of maximum

Operating pressure

Adaptor

(mm)

(mm)

(mm)

(mm)

spiral (mm)

C

extension (m)

D

at +20°C (bar)

(thread)

E

PA330600328

6

4

64

52

200

3

31

1⁄4

PA330600428

6

4

64

52

250

3,75

31

1⁄4

PA330600528

6

4

64

52

333

5

31

1⁄4

PA330600828

6

4

64

52

500

7,50

31

1⁄4

PA330601528

6

4

64

52

1000

15

31

1⁄4

PA330800328

8

6

86

70

200

3

22

1⁄4

PA330800428

8

6

86

70

250

3,75

22

1⁄4

PA330800528

8

6

86

70

333

5

22

1⁄4

PA330800828

8

6

86

70

500

7,50

22

1⁄4

PA330801528

8

6

86

70

1000

15

22

1⁄4

PA331000328

10

8

105

85

210

3

17

1⁄4

PA331000428

10

8

105

85

262

3,75

17

1⁄4

PA331000528

10

8

105

85

350

5

17

1⁄4

PA331000828

10

8

105

85

525

7,50

17

1⁄4

PA331001528

10

8

105

85

1000

15

17

1⁄4

PA331200338

12

10

134

110

200

3

12

3⁄8

PA331200438

12

10

134

110

250

3,75

12

3⁄8

PA331200538

12

10

134

110

333

5

12

3⁄8

PA331200838

12

10

134

110

500

7,50

12

3⁄8

PA331201538

12

10

134

110

1000

15

12

3⁄8

PA331500348

15

12

190

160

166

3

17

1⁄2

PA331500448

15

12

190

160

207

3,75

17

1⁄2

PA331500548

15

12

190

160

277

5

17

1⁄2

PA331500848

15

12

190

160

415

7,50

17

1⁄2

Mounting Method: Male thread and swivel fitting at both ends. Pneuflex Spring Coils are coloured yellow. Coils of 4 and 5 mm tube are available special order.

Warning

These products are intended for use in industrial compressed air systems only. Do not use these products where

pressures and temperatures can

exceed those listed under ‘Technical Data’.

Before using these products with fluids other than those specified, for non-industrial applications, life-support systems, or other applications not

within published specifications, consult Norgren.

Through misuse, age, or malfunction, components used in fluid power systems can fail in various modes. The system designer is warned to consider

the failure modes of all component parts used in fluid power systems and to provide adequate safeguards to prevent personal injury or damage to

equipment in the event of such failure.

System designers must provide a warning to end users in the system instructional manual if protection against a failure mode cannot be

adequately provided.

System designers and end users are cautioned to review specific warnings found in instruction sheets packed and shipped with these products

where applicable.

C

D

E

Working temperature °C

Factor

–40°C to +20°C

1,00

+30°C

0,83

+40°C

0,72

+50°C

0,64

+60°C

0,57

+80°C

0,47

To calculate working pressures at various temperatures, multiply

working pressure at –40°C to +20°C by factor given in table.

Maximum continuous working temperature +80°C.

Working pressure/temperature conversion factors