TUSB4041IPAPR.A datasheet(5/48 Pages) TI2

5 / 48 page

TUSB4041I

www.ti.com

SLLSEK3E – JULY 2015 – REVISED SEPTEMBER 2017

Product Folder Links: TUSB4041I

Submit Documentation Feedback

Pin Functions (continued)

I/O(1)

TYPE(1)

DESCRIPTION

NAME

NO.

—

Crystal output. This pin is the crystal output for the internal oscillator. If the XI pin is

driven by an external oscillator, this pin may be left unconnected. When using a

crystal, a 1-M

Ω feedback resistor is required between the XI and XO pins.

USB UPSTREAM SIGNALS

USB_DM_UP

I/O

—

USB high-speed differential transceiver (negative)

USB_DP_UP

I/O

—

USB high-speed differential transceiver (positive)

USB_R1

—

Precision resistor reference. Connect a 9.53-k

Ω ±1% resistor between the USB_R1

pin and ground.

USB_VBUS

—

USB upstream port power monitor. The VBUS detection requires a voltage divider.

The signal USB_VBUS must be connected to VBUS through a 90.9-k

Ω ±1% resistor

and to ground through a 10-k

Ω ±1% resistor from the signal to ground.

USB DOWNSTREAM SIGNALS

OVERCUR1z

USB port 1 overcurrent detection. This pin is used to connect the overcurrent output

of the downstream port power switch for port 1.

0 = An overcurrent event occurred.

1 = An overcurrent event has not occurred.

This pin can be left unconnected if power management is not implemented. If power

management is enabled, the necessary external circuitry should be determined by the

power switch.

OVERCUR2z

USB port 2 overcurrent detection. This pin is used to connect the overcurrent output

of the downstream port power switch for port 2.

0 = An overcurrent event occurred.

1 = An overcurrent event has not occurred.

If power management is not implemented, leave this pin unconnected. If power

management is enabled, the necessary external circuitry should be determined by the

power switch.

OVERCUR3z

USB port 3 overcurrent detection. This pin is used to connect the overcurrent output

of the downstream port power switch for port 3.

0 = An overcurrent event occurred.

1 = An overcurrent event has not occurred.

This pin can be left unconnected if power management is not implemented. If power

management is enabled, the necessary external circuitry should be determined by the

power switch.

OVERCUR4z

USB port 4 overcurrent detection. This pin is used to connect the overcurrent output

of the downstream port power switch for port 4.

0 = An overcurrent event occurred.

1 = An overcurrent event has not occurred.

This pin can be left unconnected if power management is not implemented. If power

management is enabled, the necessary external circuitry should be determined by the

power switch.

PWRCTL1/BATEN1

I/O

USB port 1 power-on control for downstream power and battery charging enable. The

pin is used for control of the downstream power switch for port 1.

The value of the pin is sampled at the deassertion of reset to determine the value of

the battery charging support for port 1 as indicated in the Battery Charging Support

0 = Battery charging not supported

1 = Battery charging supported

PWRCTL2/BATEN2

I/O

USB port 2 power-on control for downstream power and battery charging enable. The

pin is used for control of the downstream power switch for port 2.

The value of the pin is sampled at the deassertion of reset to determine the value of

the battery charging support for Port 2 as indicated in the Battery Charging Support

0 = Battery charging not supported

1 = Battery charging supported

TUSB4041IPAPR.A 数据表(PDF) 5 Page - Texas Instruments

TUSB4041IPAPR.A 数据表(HTML) 5 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48

数据表下载

链接网址

TUSB4041IPAPR.A 数据表(PDF) 5 Page - Texas Instruments

TUSB4041IPAPR.A 数据表(HTML) 5 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48

数据表 下载

链接网址

数据表下载