01/98

N/AL 9.12.001.05

Metric Tubing and Hose

Our policy is one of continuous research and development. We therefore reserve the right

to amend, without notice, the specifications given in this document.

Product

O/D I/D

Wall

Min

Recommended

Number

tube tube thickness bend safe working

10m coils

size size

radius pressure (bar)

-200°C to +50°C

CS6004010 4

2,8

0,6

12

128

CS6005010 5

3,4

0,8

15

138

CS6006010 6

4,4

0,8

19

112

CS6008010 8

6,4

0,8

24

81

CS6010010 10

8,4

0,8

30

64

3m straight

CS6012003 12

9,6

1,2

40

81

CS6016003 16

13,6 1,2

48

59

CS6022003 22

19,0 1,5

67

53

CS6028003 28

25,0 1,5

86

41

The following technical information is valid for copper tube when used with compression fittings, see Section 9.5.

For further information please consult our Technical Service.

Copper Tubing

Standard Duty: Annealed

Manufactured to BS 2871: Part 2 with dimensions

generally to Table 4.

Tolerances on O/D are +0,00mm to –0,08mm.

The recommended safe working pressures are calculated in accordance with BS1306 with a stress

value of 41N/mm2 and minimum tube wall thickness. For safe working pressures at temperatures

other than -200°c to +50°C refer to Pressure De-rating Factor table below.

Copper Tubing Pressure De-rating Factor

For temperatures other than -200°C to +50°C

Tube

-200°C

+50°C

+100°C +150°C +175°C

to

to

to

to

to

+50°C

+100°C +150°C +175°C +200°C

Annealed 1,0

0,97

0,82

0,63

0,43

Half-hard 1,0

0,95

0,88

0,54

0,29

To calculate the working pressure at temperatures other than –200°C to +50°C multiply the

working pressure given in the appropriate table by the factor given in this table.e.g. Safe working

pressure of standard duty half-hard copper tube,

8 mm O/D at +120°C = 157 x 0,88 = 138 bar.

Product

O/D I/D

Wall

Min

Recommended

Number

tube tube thickness bend safe working

3m straight size size

radius pressure (bar)

-200°C to +50°C

CS7004003 4

2,8

0,6

12

193

CS7005003 5

3,4

0,8

15

208

CS7006003 6

4,0

1,0

19

218

CS7008003 8

6,0

1,0

24

157

CS7010003 10

7,6

1,2

30

150

CS7012003 12

9,6

1,2

40

122

CS7016003 16

13,6 1,2

48

89

CS7022003 22

19,0 1,5

67

81

CS7028003 28

25,0 1,5

86

62

Standard Duty: Half Hard

Manufactured to BS 2871: Part 2 with dimensions

generally to Table 4.

Tolerances on O/D are +0,00mm to –0,08mm.

The recommended safe working pressures are calculated in accordance with BS1306 with a

stress value of 62N/mm2 and minimum tube wall thickness. For safe working pressures at

temperatures other than -200°c to +50°C refer to Pressure De-rating Factor table below.

Product

Description

Number

M/3314

Tube cutter

39012061

Replacement blades

Tube Cutter - Plastic Tubing

Suitable for providing clean square cuts through 3mm to 19mm plastic tubing.

Cutter is provided with Norgren branding in corporate red colour.

79mm

Warning

These products are intended for use in industrial compressed air systems only. Do not use these products where

pressures and temperatures can

exceed those listed under ‘Technical Data’.

Before using these products with fluids other than those specified, for non-industrial applications, life-support systems, or other applications not

within published specifications, consult Norgren.

Through misuse, age, or malfunction, components used in fluid power systems can fail in various modes. The system designer is warned to

consider the failure modes of all component parts used in fluid power systems and to provide adequate safeguards to prevent personal injury or

damage to equipment in the event of such failure.

System designers must provide a warning to end users in the system instructional manual if protection against a failure mode cannot be

adequately provided.

System designers and end users are cautioned to review specific warnings found in instruction sheets packed and shipped with these products

where applicable.