19

19

6-SPt

ACt-n

Setpoint

Select

SPSEL

Setpoint

Value

SP-n

Output

Logic

out-n

HYS-n

Setpoint

Hysteresis

tON-n

On Time

Delay

Off Time

Delay

tOF-n

Standby

Operation

Stb-n

Reset

Action

rSt-n

PAR

Pro

Setpoint

Action

Lit-n

Setpoint

Annunciators

ASn-n

Setpoint

Action

Setpoint

Assignment

6.6 mOdUle 6 - seTPOinT (alarm) ParameTers () Ñ

PARAMETER MENU

Repeat programming for each setpoint.

Enter the action for the selected setpoint (alarm output).

See the Setpoint Alarm Figures in the Setpoint Card Bulletin for a visual

detail of each action. The Inside Band action is shown here as it only applies to

the PAXDP.

SETPOINT ASSIGNMENT























Selects the meter value that is used to trigger the Setpoint Alarm. The 

settings cause the setpoint to trigger off of the relative (net) input value. The

relative input value is the absolute input value that includes the Display Offset

Value. The  settings cause the setpoint to trigger off of the absolute (gross)

input value. The absolute input value is based on Module 1  and  entries.

SETPOINT ACTION



















 *

 *

 *



 **

 **

















SELECT SETPOINT

Select a setpoint (alarm output) to open the remaining module menu. (The

“” in the following parameters will reflect the chosen setpoint number.) After

the chosen setpoint is programmed, the display will default to  . Select

the next setpoint to be programmed and continue the sequence for each setpoint.

Pressing

PAR at   will exit Module 6.





No Setpoint Action

=



Absolute high, with balanced hysteresis

=



Absolute low, with balanced hysteresis

=



Absolute high, with unbalanced hysteresis

=



Absolute low, with unbalanced hysteresis

=



Deviation high, with unbalanced hysteresis *

=



= Deviation low, with unbalanced hysteresis *





Inside band, with unbalanced hysteresis *

Outside band, with unbalanced hysteresis *

=

=



Lower Totalizer absolute high, unbalance hysteresis **

=



Upper Totalizer absolute high, unbalance hysteresis **

=

* Setpoint 2 or Setpoint 4 deviation and band action setpoints are relative to

the value of setpoint 1 or Setpoint 3 respectively. It is not possible to configure

setpoint 1 or 3 as deviation or band actions. It is possible to use setpoint 1 or 3

for an absolute action, while its value is being used for deviation or band.

** These modes only appear, and are the only modes that appear, when the

setpoint assignment  is set to . The lower Totalizer action, ,

allows setpoints to function off of the lower 5 digits of the Totalizer. The upper

Totalizer action,  , allows setpoints to function off of the upper 4 digits

of the Totalizer. To obtain absolute low alarms for the Totalizer, program the



or  output logic as reverse.

Ñ

- A setpoint card must be installed in order to access this module.

Setpoint Alarm Figures

With reverse output logic , the below alarm states are opposite.

ALARM

STATE

OFF

ON

Hys

SP + Hys

SP

OFF

TRIGGER POINTS

Absolute Low Acting (Unbalanced Hys) = 

ALARM

STATE

OFF

ON

Hys

SP + ½Hys

SP

SP - ½Hys

OFF

TRIGGER POINTS

ALARM

STATE

OFF

ON

Hys

SP1 + SPn

SP1

OFF

TRIGGER POINTS

Absolute Low Acting (Balanced Hys) = 

Deviation High Acting (SP > 0) = 

ALARM

STATE

OFF

ON

Hys

SP + ½Hys

SP

SP - ½Hys

OFF

TRIGGER POINTS

Absolute High Acting (Balanced Hys) = 

ALARM

STATE

OFF

ON

Hys

SP

SP - Hys

OFF

TRIGGER POINTS

ALARM

STATE

OFF

ON

Hys

SP1 - SPn

SP1

OFF

TRIGGER POINTS

Absolute High Acting (Unbalanced Hys) = 

This is also for Totalizer alarms: 

, 

Deviation Low Acting (SP > 0) = 