 |
数据搜索系统，热门电子元器件搜索 |
|
|
数据搜索系统，热门电子元器件搜索 |
|
STM32G030C8 数据表(PDF) 40 Page - STMicroelectronics |
|
|
|||||||||||||||||||||||||||||
STM32G030C8 数据表(HTML) 40 Page - STMicroelectronics |
|
|
40 / 94 page  Electrical characteristics STM32G030x6/x8 40/94 DS12991 Rev 1 5.2 Absolute maximum ratings Stresses above the absolute maximum ratings listed in Table 18, Table 19 and Table 20 may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these conditions is not implied. Exposure to maximum rating conditions for extended periods may affect device reliability. Table 18. Voltage characteristics Symbol Ratings Min Max Unit VDD - VSS External supply voltage -0.3 4.0 V VBAT - VSS VIN(1) Input voltage on FT_xx VSS - 0.3 VDD + 4.0(2) Input voltage on any other pin VSS - 0.3 4.0 1. Refer to Table 19 for the maximum allowed injected current values. 2. To sustain a voltage higher than 4 V the internal pull-up/pull-down resistors must be disabled. Table 19. Current characteristics Symbol Ratings Max Unit IVDD/VDDA Current into VDD/VDDA power pin (source)(1) 100 mA IVSS/VSSA Current out of VSS/VSSA ground pin (sink)(1) 100 IIO(PIN) Output current sunk by any I/O and control pin except FT_f 15 Output current sunk by any FT_f pin 20 Output current sourced by any I/O and control pin 15 ∑IIO(PIN) Total output current sunk by sum of all I/Os and control pins(2) 80 Total output current sourced by sum of all I/Os and control pins(2) 80 IINJ(PIN) (3) Injected current on a FT_xx pin -5 / NA(4) ∑|IINJ(PIN)| Total injected current (sum of all I/Os and control pins)(5) 25 1. All main power (VDD/VDDA, VBAT) and ground (VSS/VSSA) pins must always be connected to the external power supplies, in the permitted range. 2. This current consumption must be correctly distributed over all I/Os and control pins. The total output current must not be sunk/sourced within one current group as defined in Table 12: Pin assignment and description. 3. A positive injection is induced by VIN > VDDIOx while a negative injection is induced by VIN < VSS. IINJ(PIN) must never be exceeded. Refer also to Table 18: Voltage characteristics for the maximum allowed input voltage values. 4. Positive injection is not possible on these I/Os and does not occur for input voltages lower than the specified maximum value. 5. When several inputs are submitted to a current injection, the maximum ∑|IINJ(PIN)| is the absolute sum of the negative injected currents (instantaneous values). Table 20. Thermal characteristics Symbol Ratings Value Unit TSTG Storage temperature range –65 to +150 °C TJ Maximum junction temperature 150 °C |
|
链接网址 |
| ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 数据表链接 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
Chinese ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
