KW2D Series ø22 Smart RFID Reader

15

1. Notes on contents of Catalogs

(1) Rated values, performance values, and specification values of IDEC products

listed in this Catalog are values acquired under respective conditions in

independent testing, and do not guarantee values gained in combined

conditions.

Also, durability varies depending on the usage environment and usage

conditions.

(2) Reference data and reference values listed in Catalogs are for reference

purposes only, and do not guarantee that the product will always operate

appropriately in that range.

(3) The specifications / appearance and accessories of IDEC products listed in

Catalogs are subject to change or termination of sales without notice, for

improvement or other reasons.

(4) The content of Catalogs is subject to change without notice.

2. Note on applications

(1) If using IDEC products in combination with other products, confirm the

applicable laws / regulations and standards.

Also, confirm that IDEC products are compatible with your systems, machines,

devices, and the like by using under the actual conditions. IDEC shall bear no

liability whatsoever regarding the compatibility with IDEC products.

(2) The usage examples and application examples listed in Catalogs are for

reference purposes only. Therefore, when introducing a product, confirm the

performance and safety of the instruments, devices, and the like before use.

Furthermore, regarding these examples, IDEC does not grant license to use

IDEC products to you, and IDEC offers no warranties regarding the ownership

of intellectual property rights or non-infringement upon the intellectual

property rights of third parties.

(3) When using IDEC products, be cautious when implementing the following.

i.

Use of IDEC products with sufficient allowance for rating and

performance

ii. Safety design, including redundant design and malfunction prevention

design that prevents other danger and damage even in the event that an

IDEC product fails

iii. Wiring and installation that ensures the IDEC product used in your

system, machine, device, or the like can perform and function according

to its specifications

(4) Continuing to use an IDEC product even after the performance has

deteriorated can result in abnormal heat, smoke, fires, and the like due to

insulation deterioration or the like. Perform periodic maintenance for IDEC

products and the systems, machines, devices, and the like in which they are

used.

(5) IDEC products are developed and manufactured as general-purpose products

for general industrial products. They are not intended for use in the following

applications, and in the event that you use an IDEC product for these

applications, unless otherwise agreed upon between you and IDEC, IDEC shall

provide no guarantees whatsoever regarding IDEC products.

i.

Use in applications that require a high degree of safety, including nuclear

power control equipment, transportation equipment (railroads / airplanes

/ ships / vehicles / vehicle instruments, etc.), equipment for use in outer

space, elevating equipment, medical instruments, safety devices, or

any other equipment, instruments, or the like that could endanger life or

human health

ii. Use in applications that require a high degree of reliability, such as

provision systems for gas / waterworks / electricity, etc., systems that

operate continuously for 24 hours, and settlement systems

iii. Use in applications where the product may be handled or used deviating

from the specifications or conditions / environment listed in the Catalogs,

such as equipment used outdoors or applications in environments

subject to chemical pollution or electromagnetic interference

If you would like to use IDEC products in the above applications, be sure

to consult with an IDEC sales representative.

3. Inspections

We ask that you implement inspections for IDEC products you purchase without

delay, as well as thoroughly keep in mind management/maintenance regarding

handling of the product before and during the inspection.

4. Warranty

(1) Warranty period

The warranty period for IDEC products shall be one (1) year after purchase or

delivery to the specified location. However, this shall not apply in cases where

there is a different specification in the Catalogs or there is another agreement

in place between you and IDEC.

(2) Warranty scope

Should a failure occur in an IDEC product during the above warranty period

for reasons attributable to IDEC, then IDEC shall replace or repair that

product, free of charge, at the purchase location / delivery location of the

product, or an IDEC service base. However, failures caused by the following

reasons shall be deemed outside the scope of this warranty.

i.

The product was handled or used deviating from the conditions /

environment listed in the Catalogs

ii. The failure was caused by reasons other than an IDEC product

iii. Modification or repair was performed by a party other than IDEC

iv. The failure was caused by a software program of a party other than

IDEC

v. The product was used outside of its original purpose

vi. Replacement of maintenance parts, installation of accessories, or the like

was not performed properly in accordance with the user’s manual and

Catalogs

vii. The failure could not have been predicted with the scientific and

technical standards at the time when the product was shipped from

IDEC

viii. The failure was due to other causes not attributable to IDEC (including

cases of force majeure such as natural disasters and other disasters)

Furthermore, the warranty described here refers to a warranty on the IDEC

product as a unit, and damages induced by the failure of an IDEC product are

excluded from this warranty.

5. Limitation of liability

The warranty listed in this Agreement is the full and complete warranty for IDEC

products, and IDEC shall bear no liability whatsoever regarding special damages,

indirect damages, incidental damages, or passive damages that occurred due to an

IDEC product.

6. Service scope

The prices of IDEC products do not include the cost of services, such as dispatching

technicians. Therefore, separate fees are required in the following cases.

(1) Instructions for installation / adjustment and accompaniment at test operation

(including creating application software and testing operation, etc.)

(2) Maintenance inspections, adjustments, and repairs

(3) Technical instructions and technical training

(4) Product tests or inspections specified by you

The above content assumes transactions and usage within your region. Please

consult with an IDEC sales representative regarding transactions and usage outside

of your region. Also, IDEC provides no guarantees whatsoever regarding IDEC

products sold outside your region.

Ordering Terms and Conditions

Thank you for using IDEC Products.

By purchasing products listed in our catalogs, datasheets, and the like (hereinafter referred to as “Catalogs”) you agree to be bound by these terms and conditions. Please read

and agree to the terms and conditions before placing your order.