| 数据搜索系统,热门电子元器件搜索 |
|
ADS8883IDGS 数据表(PDF) 36 Page - Texas Instruments |
|
|
|||||||||||||||||||||||||||||
ADS8883IDGS 数据表(HTML) 36 Page - Texas Instruments |
|
36 / 52 page ![]() AVDD AVDD AVDD AVDD AVDD VCM 10 10 nF 0.2 10 µF Vin Temp Gnd Vout Trim REF5045 1 µF 1 k 1 µF + - + THS4281 1 k 1 µF + - + OPA333 20 k 1 µF VIN+ VIN- + + THS4521 V + AINP AINM REF GND AVDD CONVST CONVST ADS8883 10 INPUT DRIVER REFERENCE DRIVE CIRCUIT 18-Bit 680-kSPS SAR ADC - - 1 K 1 K 1 K 1 K + ADS8883 SBAS567A – MAY 2013 – REVISED DECEMBER 2013 www.ti.com DAQ Circuit for Lowest Distortion and Noise Performance at 680 kSPS This section describes two application circuits (Figure 72 and Figure 73) that are optimized for using the ADS8883 with lowest distortion and noise performance at a throughput of 680 kSPS. In both applications, the input signal is processed through a high-bandwidth, low-distortion, fully-differential amplifier (FDA) designed in an inverting gain configuration and a low-pass RC filter before being fed into the ADC. As a rule of thumb, the distortion from the input driver should be at least 10 dB less than the ADC distortion. The distortion resulting from variation in the common-mode signal is eliminated by using the FDA in an inverting gain configuration that establishes a fixed common-mode level for the circuit. This configuration also eliminates the requirement of a rail-to-rail swing at the amplifier input. Therefore, these circuits use the low-power THS4521 as an input driver, which provides exceptional ac performance because of its extremely low-distortion and high- bandwidth specifications. In addition, the components of the antialiasing filter are such that the noise from the front-end circuit is kept low without adding distortion to the input signal. Differential Input Configuration The circuit in Figure 72 shows a fully-differential DAQ block optimized for low distortion and noise using the THS4521 and ADS8883. This front-end circuit configuration requires a differential signal at the input of the FDA and provides a differential output to drive the ADC inputs. The common-mode voltage of the input signal provided to the ADC is set by the VOCM pin of the THS4521 (not shown in Figure 72). To use the complete dynamic range of the ADC, VOCM can be set to VREF / 2 by using a simple resistive divider. However, note that the ADS8883 allows the common-mode input voltage (VCM) to be set to any value in the range of 0 V to VREF. Figure 72. Differential Input DAQ Circuit for Lowest Distortion and Noise at 680 kSPS For step-by-step design procedure, circuit schematics, bill of materials, PCB files, simulation results, and test results, using a similar device, refer to 18-Bit, 1-MSPS Data Acquisition (DAQ) Block Optimized for Lowest Distortion and Noise (SLAU515). 36 Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: ADS8883 |
|
链接网址 |
| ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 数据表链接 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |