BQ25713 datasheet(5/111 Pages) TI2

5 / 111 page

6 Pin Configuration and Functions

VBUS

HIDRV2

ACN

SW2

ACP

VSYS

CHRG_OK

BATDRV

OTG/VAP/FRS

SRP

ILIM_HIZ

SRN

VDDA

CELL_BATPRESZ

IADPT

COMP2

Thermal

Pad

Figure 6-1. RSN Package 32-Pin WQFN Top View

Table 6-1. Pin Functions

I/O

DESCRIPTION

NAME

NUMBER

ACN

PWR

Input current sense amplifier negative input. The leakage on ACP and ACN are matched. A

RC low-pass filter is required to be placed between the sense resistor and the ACN pin to

suppress the high frequency noise in the input current signal. Refer to Section 9.2.2.2 for

ACP/ACN filter design.

ACP

PWR

Input current sense amplifier positive input. The leakage on ACP and ACN are matched. A

RC low-pass filter is required to be placed between the sense resistor and the ACP pin to

suppress the high frequency noise in the input current signal. Refer to Section 9.2.2.2 for

ACP/ACN filter design.

BATDRV

P-channel battery FET (BATFET) gate driver output. It is shorted to VSYS to turn off the

BATFET. It goes 10 V below VSYS to fully turn on BATFET. BATFET is in linear mode to

regulate VSYS at minimum system voltage when battery is depleted. BATFET is fully on

during fast charge and works as an ideal-diode in supplement mode.

BTST1

PWR

Buck mode high-side power MOSFET driver power supply. Connect a 0.047-µF capacitor

between SW1 and BTST1. The bootstrap diode between REGN and BTST1 is integrated.

BTST2

PWR

Boost mode high-side power MOSFET driver power supply. Connect a 0.047-μF capacitor

between SW2 and BTST2. The bootstrap diode between REGN and BTST2 is integrated.

CELL_BATPRESZ

Battery cell selection pin for 1- to 5- cell battery setting. CELL_BATPRESZ pin is biased

from VDDA through a resistor divider. CELL_BATPRESZ pin also sets SYSOVP thresholds

to 5 V for 1-cell, 12 V for 2-cell and 19.5 V for 3-cell/4-cell. CELL_BATPRESZ pin is

pulled below VCELL_BATPRESZ_FALL to indicate battery removal. After battery is removed the

charge voltage register REG0x05/04h() goes back to default. No external cap is allowed

at CELL_BATPRESZ pin. The device exits LEARN mode and disables charge when

CELL_BATPRESZ pin is pulled low (upon battery removal).

www.ti.com

BQ25730

SLUSE65A – FEBRUARY 2021 – REVISED JANUARY 2024

Submit Document Feedback

Product Folder Links: BQ25730

BQ25713 数据表(PDF) 5 Page - Texas Instruments

BQ25713 数据表(HTML) 5 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载