LM393DGKR.A datasheet(7/56 Pages) TI2

7 / 56 page

5.6 Electrical Characteristics LM2903B

VS = 5V, VCM = (V–) ; TA = 25°C (unless otherwise noted).

PARAMETER

TEST CONDITIONS

MIN

TYP

MAX

UNIT

VIO

Input offset voltage

VS = 5 to 36V

–2.5

±0.37

2.5

VS = 5 to 36V, TA = –40°C to +125°C

–4

Input offset voltage, DGK package

only

VS = 5 to 36V

-3.5

±0.37

3.5

VS = 5 to 36V, TA = –40°C to +125°C

-5

Input bias current

–3.5

–25

TA = –40°C to +125°C

–50

IOS

Input offset current

–10

±0.5

TA = –40°C to +125°C

–25

VCM

Common mode range (1)

VS = 3 to 36V

(V–)

(V+) – 1.5

VS = 3 to 36V, TA = –40°C to +125°C

(V–)

(V+) – 2.0

AVD

Large signal differential voltage

amplification

VS = 15V, VO = 1.4V to 11.4V;

RL ≥ 15k to (V+)

200

V/mV

VOL

Low level output Voltage {swing

from (V–)}

ISINK ≤ 4mA, VID = -1V

110

400

ISINK ≤ 4mA, VID = -1V

TA = –40°C to +125°C

550

IOH-LKG

High-level output leakage current

(V+) = VO = 5V; VID = 1V

0.1

(V+) = VO = 36V; VID = 1V

0.3

IOL

Low level output current

VOL = 1.5V; VID = -1V; VS = 5V

Quiescent current (all comparators)

VS = 5V, no load

400

600

µA

VS = 36V, no load, TA = –40°C to +125°C

550

800

µA

(1)

The voltage at either input can not be allowed to go negative by more than 0.3V otherwise output can be incorrect and excessive

input current can flow. The upper end of the common-mode voltage range is limited by VCC – 2V. However only one input needs to be

in the valid common mode range, the other input can go up the maximum VCC level and the comparator provides a proper output state.

Either or both inputs can go to maximum VCC level without damage.

5.7 Switching Characteristics LM393B and LM2903B

VS = 5V, VO_PULLUP = 5V, VCM = VS/2, CL = 15pF, RL = 5.1k Ohm, TA = 25°C (unless otherwise noted).

PARAMETER

TEST CONDITIONS

MIN

TYP

MAX

UNIT

tresponse

Propagation delay time, high-to-low;

TTL input signal (1)

TTL input with Vref = 1.4V

300

tresponse

Propagation delay time, high-to-low;

Small scale input signal (1)

Input overdrive = 5mV, Input step = 100mV

1000

(1)

High-to-low and low-to-high refers to the transition at the input.

www.ti.com

LM393B, LM2903B, LM193, LM293, LM293A, LM393, LM393A, LM2903, LM2903V

SLCS005AH – OCTOBER 1979 – REVISED APRIL 2025

Submit Document Feedback

Product Folder Links: LM393B LM2903B LM193 LM293 LM293A LM393 LM393A LM2903 LM2903V

LM393DGKR.A 数据表(PDF) 7 Page - Texas Instruments

LM393DGKR.A 数据表(HTML) 7 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56

数据表下载

链接网址

LM393DGKR.A 数据表(PDF) 7 Page - Texas Instruments

LM393DGKR.A 数据表(HTML) 7 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56

数据表 下载

链接网址

数据表下载