V10

2

SPECIFICATIONS

All Specifications Typical At Nominal Line, Full Load, and 25℃ Unless Otherwise Noted

INPUT SPECIFICATIONS:

GENERAL SPECIFICATIONS:

Input Voltage Range ........……………..................... 24V ..................... 9-36V

Efficiency

.................................................................…..……... See Table

48V.................... 18-75V

Isolation Voltage ..........….. Input/Output ….…....……..…. 3000VDC min.

Input Surge Voltage (100 ms max.) …………...…….. 24V ……… 50VDC max.

Input/Output .......................

2000VAC min.

48V……. 100VDC max.

Isol

ation Resistance .................................…...............……. 109 ohm min.

Input Filter ………………………………………………..……..…….... Capacitive

Isolation Capacitance

…………………………………………... 50pF max.

Remote On/Off Control:

Switching Frequency ...................

........…..................…….... 530KHz typ.

Module On …………………………… Open or High Impedance

Operating Ambient Temperature ……………..…... -40℃ to +85℃

Module Off

………………………………………… 2mA to 4mA

De-rating, Above 50℃

………..………. Linearly to Zero power at 105℃

Module Off (Input Idle C

urrent) …….…………...… 2.5mA max.

Case Temperature (note4) ……………………….…………. 105℃ max.

OUTPUT SPECIFICATIONS:

Cooling

……………………….…………….…………. Natural Convection

Voltage Accuracy ............................................……….................

1.0% max. Storage Temperature ………………....….........…........ -55℃ to +125℃

Voltage Balance

(Dual) ……………………………………………....

1.0% max Humidity …………………………….……. 95% RH max. Non condensing

Transient Response: 75%~100% Step Load Change

MTBF …. MIL-HDBK-217F, GB, 25℃, Full Load ……..… 1930Khrs typ.

Error Band ……

5% Vout Nominal, Recovery Time …….….. < 250μs Dimensions …..…..............… 0.87x0.37x0.47 inches (22.0x9.5x12.0mm)

Ripple & Noise, 20MHz BW (Note 5) .... 3.3V & 5V & ±5V

… 100mV pk-pk max.

Cas

e Material ……………………………… Non-Conductive Black Plastic

12V/15V/±12V/±15V…..... 1%Vo max.

Weight

……………………………………………….…………………... 4.9g

Temperature Coefficient ....................……….....….................

0.02%/C max. NOTE:

Short Circuit Protection ...................................................

......….…. Continuous

1. Measured from high line to low line.

Line Regulation (note1) .…….………………..….......................….

0.2% max. 2. Measured from full load to no load.

Load Regulation (note2) ……..………….......................…............

1.0% max. 3. For asymmetric loading, both channels must be at 25% load or more.

Cross Regulation

(Dual note3) … Asymmetrical Load 25%/100% ..

5.0% max. 4. Maximum case temperature under any operating condition should

Current Limit …………………………………………………………...180% typ.

not be exceeded 105℃.

Start up time ……………………………….......................……… 5ms typ.

5. Output ripple and noise measured with 1uF ceramic capacitor

CASE SA DIMENSIONS:

Bottom View

PIN CONNECTION

Pin

Single

Dual

1

-V Input

-V Input

2

+V Input

+V Input

3

On/Off

On/Off

6

+V Output

+V Output

7

-V Output

Common

8

NC

-V Output

All Dimensions In Inches (mm)

Tolerances：Inches

Millimeters

X.XX=±0.02

X. X=±0.5

Pin

±0.002

±0.05

0.87 (22.0)

0.08 (2.1)

0.02 (0.5)

1

2 3

6

7 8

0.70 (17.8)

0.10 (2.5)

Load (%)

100

50

-40

71

100

(Deg. C)

a. Operating Temperature : -40

C to 71C ---> without derating

b. Operating Temperature : 71

C to 100C ---> derating (-3.45%/C)

Derating Curve :

-3.45%/

C

Fig1. Input Voltage Derating Curve

Fig2. Typical Derating Curve for Naturel Convection