ADE7566 datasheet(68/144 Pages) AD

68 / 144 page

ADE7566/ADE7569/ADE7166/ADE7169

Rev. A | Page 68 of 144

The gain of the apparent energy can be adjusted by using the

multiplier and by writing a twos complement, 12-bit word to the

VAGAIN register (VAGAIN[11:0]). Equation 32 shows how the

gain adjustment is related to the contents of the VAGAIN register.

APPARENT POWER CALCULATION

Apparent power is defined as the maximum power that can be

delivered to a load. Vrms and Irms are the effective voltage and

current delivered to the load, respectively. Therefore, the apparent

power (AP) = Vrms × Irms. This equation is independent from the

phase angle between the current and the voltage.

Output VAGAIN

⎟

⎠

⎞

⎜

⎝

⎛

⎭

⎬

⎫

⎩

⎨

⎧ +

VAGAIN

Power

Apparent

(32)

Equation 31 gives an expression of the instantaneous power

signal in an ac system with a phase shift.

()

sin( )

rms

(28)

()

)

sin(

rms

(29)

)

(

)

(

)

(

(30)

( )

)

cos(

)

cos(

−

rms

(31)

For example, when 0x7FF is written to the VAGAIN register, the

power output is scaled up by 50% (0x7FF = 2047d, 2047/212 = 0.5).

Similarly, 0x800 = –2047d (signed twos complement) and power

output is scaled by –50%. Each LSB represents 0.0244% of the

power output. The apparent power is calculated with the current

and voltage rms values obtained in the rms blocks of the

ADE7566/ADE7569/ADE7166/ADE7169.

Apparent Power Offset Calibration

Figure 75 illustrates the signal processing for the calculation of

the apparent power in the ADE7566/ADE7569/ADE7166/

ADE7169.

Each rms measurement includes an offset compensation register to

calibrate and eliminate the dc component in the rms value (see the

Current Channel RMS Calculation section and the Voltage

Channel RMS Calculation

The apparent power signal can be read from the waveform register

by setting the WAVMODE register (0x0D) and setting the WFSM

bit in the Interrupt Enable 3 SFR (MIRQENH, 0xDB). Like the

current and voltage channel waveform sampling modes, the

waveform data is available at sample rates of 25.6 kSPS,

12.8 kSPS, 6.4 kSPS, or 3.2 kSPS.

section). The voltage and current

channels rms values are then multiplied together in the

apparent power signal processing. Because no additional offsets

are created in the multiplication of the rms values, there is no

specific offset compensation in the apparent power signal

processing. The offset compensation of the apparent power

measurement is done by calibrating each individual rms

measurement.

Vrms

Irms

0x1A36E2

APPARENT POWER

SIGNAL (P)

CURRENT RMS SIGNAL – i(t)

VOLTAGE RMS SIGNAL – v(t)

0x00

0x1CF68C

0x00

0x1CF68C

VAGAIN

DIGITAL-TO-FREQUENCY

CONVERTER

VARMSCFCON

Figure 75. Apparent Power Signal Processing

ADE7566 数据表(PDF) 68 Page - Analog Devices

ADE7566 数据表(HTML) 68 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载