ISL54053_0709 datasheet(3/11 Pages) INTERSIL

3 / 11 page

FN6460.2

September 25, 2007

Absolute Maximum Ratings

Thermal Information

V+ to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to 6.5V

Input Voltages

NO, NC, IN (Note 2) . . . . . . . . . . . . . . . . . . . -0.5 to ((V+) + 0.5V)

Output Voltages

COM (Note 2) . . . . . . . . . . . . . . . . . . . . . . . . -0.5 to ((V+) + 0.5V)

Continuous Current NO, NC, or COM . . . . . . . . . . . . . . . . .

±300mA

Peak Current NO, NC, or COM

(Pulsed 1ms, 10% Duty Cycle, Max) . . . . . . . . . . . . . . . .

±500mA

ESD Rating

Human Body Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .>6kV

Machine Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .>200V

Charged Device Model . . . . . . . . . . . . . . . . . . . . . . . . . . . .>1000V

Operating Conditions

V+ (Positive DC Supply Voltage) . . . . . . . . . . . . . . . . . 1.8V to 5.5V

Analog Signal Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0V to V+

VIN (Digital Logic Input Voltage (IN). . . . . . . . . . . . . . . . . . 0V to V+

Temperature Range . . . . . . . . . . . . . . . . . . . . . . . -40°C to +85°C

Thermal Resistance (Typical, Note 3)

θJA (°C/W)

6 Ld

μTDFN Package . . . . . . . . . . . . . . . . . . . . . . .

175

Maximum Junction Temperature (Plastic Package). . . . . . . +150°C

Maximum Storage Temperature Range . . . . . . . . . . . -65°C to +150°C

Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . .see link below

http://www.intersil.com/pbfree/Pb-FreeReflow.asp

CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and

result in failures not covered by warranty.

NOTES:

2. Signals on NC, NO, IN, or COM exceeding V+ or GND are clamped by internal diodes. Limit forward diode current to maximum current ratings.

θJA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details.

Electrical Specifications - 5V Supply

Test Conditions: V+ = +4.5V to +5.5V, GND = 0V, VINH = 2.4V, VINL = 0.8V (Note 4), Unless

Otherwise Specified.

PARAMETER

TEST CONDITIONS

TEMP

(°C)

MIN

(Notes 5, 6)

TYP

MAX

(Notes 5, 6) UNITS

ANALOG SWITCH CHARACTERISTICS

Analog Signal Range, VANALOG

Full

V+

ON-Resistance, rON

V+ = 4.5V, ICOM = 100mA, VNO or VNC = 0V to V+,

(See Figure 5)

0.86

Full

rON Matching Between Channels,

Δr

V+ = 4.5V, ICOM = 100mA, VNO or VNC = 2.5V

0.004

Full

0.004

rON Flatness, rFLAT(ON)

V+ = 4.5V, ICOM = 100mA, VNO or VNC = 0V to V+,

(Note 7)

0.25

Full

0.27

NO or NC OFF Leakage Current,

INO(OFF) or INC(OFF)

V+ = 5.5V, VCOM = 0.3V, 5V, VNO or VNC = 5V, 0.3V

-10

Full

-150

150

COM ON Leakage Current,

ICOM(ON)

+ = 5.5V, VCOM = 0.3V, 5V, or VNO or VNC = 0.3V, 5V,

or floating

-20

Full

-300

300

DYNAMIC CHARACTERISTICS

Turn-ON Time, tON

V+ = 4.5V, VNO or VNC = 3.0V, RL = 50Ω, CL = 35pF

(See Figure 1, Note 8)

Full

Turn-OFF Time, tOFF

V+ = 4.5V, VNO or VNC = 3.0V, RL = 50Ω, CL = 35pF

(See Figure 1, Note 8)

Full

Break-Before-Make Time Delay, tD

V+ = 5.5V, VNO or VNC = 3.0V, RL = 50Ω, CL = 35pF

(See Figure 3, Note 8)

Full

Charge Injection, Q

VG = 0V, RG = 0Ω, CL = 1.0nF (See Figure 2)

OFF Isolation

RL = 50Ω, CL = 5pF, f = 100kHz, VCOM = 1VRMS

(See Figure 4)

Crosstalk (Channel-to-Channel)

RL = 50Ω, CL = 5pF, f = 100kHz, VCOM = 1VRMS

(See Figure 6)

-83

Total Harmonic Distortion

f = 20Hz to 20kHz, VCOM = 0.5VP-P, RL = 600Ω

0.03

ISL54053

ISL54053_0709 数据表(PDF) 3 Page - Intersil Corporation

ISL54053_0709 数据表(HTML) 3 Page - Intersil Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11

数据表下载

链接网址

ISL54053_0709 数据表(PDF) 3 Page - Intersil Corporation

ISL54053_0709 数据表(HTML) 3 Page - Intersil Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11

数据表 下载

链接网址

数据表下载