STM32L4P5CEU6P datasheet(137/311 Pages) STMICROELECTRONICS

137 / 311 page

DS12903 Rev 2

137/311

STM32L4P5xx

Electrical characteristics

277

|∆VDDx|

Variations between different VDDX power pins

of the same domain

-50

|VSSx-VSS|

Variations between all the different ground

pins(5)

-50

VREF+ - VDDA Allowed voltage difference for VREF+ > VDDA

-0.4

1. All main power (VDD, VDDA, VDDIO2, VDDUSB, VBAT) and ground (VSS, VSSA) pins must always be

connected to the external power supply, in the permitted range.

2. VIN maximum must always be respected. Refer to Table 19: Current characteristics for the maximum

allowed injected current values.

3. This formula has to be applied only on the power supplies related to the IO structure described in the pin

definition table.

4. To sustain a voltage higher than 4 V the internal pull-up/pull-down resistors must be disabled.

5. Include VREF- pin.

Table 19. Current characteristics

Symbol

Ratings

Max

Unit

∑IVDD

Total current into sum of all VDD power lines (source)(1) (2)

1. All main power (VDD, VDDA, VDDIO2, VDDUSB, VBAT) and ground (VSS, VSSA) pins must always be

connected to the external power supplies, in the permitted range.

2. Valid also for VDD12 on SMPS package.

200

∑IVSS

Total current out of sum of all VSS ground lines (sink)(1) (2)

200

IVDD(PIN)

Maximum current into each VDD power pin (source)(1)

100

IVSS(PIN)

Maximum current out of each VSS ground pin (sink)(1)

100

IIO(PIN)

Output current sunk by any I/O and control pin except FT_f

Output current sunk by any FT_f pin

Output current sourced by any I/O and control pin

∑IIO(PIN)

Total output current sunk by sum of all I/Os and control pins(3)

3. This current consumption must be correctly distributed over all I/Os and control pins. The total output

current must not be sunk/sourced between two consecutive power supply pins referring to high pin count

QFP packages.

100

Total output current sourced by sum of all I/Os and control pins(3)

100

IINJ(PIN)(4)

4. Positive injection (when VIN > VDDIOx) is not possible on these I/Os and does not occur for input voltages

lower than the specified maximum value.

Injected current on FT_xxx, TT_xx, RST and B pins, except PA4, PA5 -5/+0(5)

5. A negative injection is induced by VIN < VSS. IINJ(PIN) must never be exceeded. Refer also to Table 18:

Voltage characteristics for the minimum allowed input voltage values.

Injected current on PA4, PA5

-5/0

∑|IINJ(PIN)| Total injected current (sum of all I/Os and control pins)(6)

6. When several inputs are submitted to a current injection, the maximum ∑|IINJ(PIN)| is the absolute sum of

the negative injected currents (instantaneous values).

Table 18. Voltage characteristics(1) (continued)

Symbol

Ratings

Min

Max

Unit

STM32L4P5CEU6P 数据表(PDF) 137 Page - STMicroelectronics

STM32L4P5CEU6P 数据表(HTML) 137 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载