| 数据搜索系统,热门电子元器件搜索 |
|
LNBP21 数据表(PDF) 7 Page - STMicroelectronics |
|
|
|||||||||||||||||||||||||||||
LNBP21 数据表(HTML) 7 Page - STMicroelectronics |
|
7 / 20 page ![]() LNBP21 7/20 LNBP1 SOFTWARE DESCRIPTION INTERFACE PROTOCOL The interface protocol comprises: - A start condition (S) - A chip address byte = hex 10 / 11 (the LSB bit determines read(=1)/write(=0) transmission) - A sequence of data (1 byte + acknowledge) - A stop condition (P) ACK= Acknowledge S= Start P= Stop R/W= Read/Write SYSTEM REGISTER (SR, 1 BYTE) R,W= read and write bit R= Read-only bit All bits reset to 0 at Power-On TRANSMITTED DATA (I2CBUS WRITE MODE) When the R/W bit in the chip address is set to 0, the main µP can write on the System Register (SR) of the LNBP21 via I2C bus. Only 6 bits out of the 8 available can be written by the µP, since the re-maining 2 are left to the diagnostic flags, and are read-only. X= don't care. Values are typical unless otherwise specified RECEIVED DATA (I2C bus READ MODE) The LNBP21 can provide to the Master a copy of the SYSTEM REGISTER information via I2C bus in read mode. The read mode is Master activated by sending the chip address with R/W bit set to 1. At the following master generated clocks bits, the LNBP21 issues a byte on the SDA data bus line (MSB transmitted first). At the ninth clock bit the MCU master can: - acknowledge the reception, starting in this way the transmission of another byte from the LNBP21; CHIP ADDRESS DATA MSB LSB MSB LSB S 0001000 R/W ACK ACK P MSB LSB R, W R, W R, W R, W R, W R, W R R PCL ISEL TEN LLC VSEL EN OTF OLF PCL ISEL TEN LLC VSEL EN OTF OLF Function 001 X X VOUT=13V, VUP=16V Loopthrough switch open 011 X X VOUT=18V, VUP=21V Loopthrough switch open 101 X X VOUT=14V, VUP=17V Loopthrough switch open 111 X X VOUT=19V, VUP=22V Loopthrough switch open 0 1 X X 22KHz tone is controlled by DSQIN pin 1 1 X X 22KHz tone is ON, DSQIN pin disabled 01 X X IOUT(min)=500mA, IOUT(max)=650mA ISC=300mA 11 X X IOUT(min)=400mA, IOUT(max)=550mA ISC=300mA 0 1 X X Pulsed (dynamic) current limiting is selected 1 1 X X Static current limiting is selected X X X X X 0 X X Power blocks disabled, Loopthrough switch closed |
|
|
链接网址 |
| ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 数据表链接 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |