E5DC-RX0ASM-015 datasheet(10/112 Pages) OMRON

10 / 112 page

E5GC

USB-Serial Conversion Cable

Windows is a registered trademark of Microsoft Corporation in the

United States and or other countries.

Use a high-power port for the USB port.

Note: A driver must be installed on the computer. Refer to the

Instruction Manual included with the Cable for the installation

procedure.

Communications Specifications

* The baud rate, data bit length, stop bit length, and vertical parity can

be individually set using the Communications Setting Level.

Communications Functions

MELSEC is a registered trademark of Mitsubishi Electric Corporation.

KEYENCE is a registered trademark of Keyence Corporation.

Both the programless communications and the component communications

support the copying.

Current Transformer (Order Separately)

Ratings

Heater Burnout Alarms and SSR Failure

Alarms

For heater burnout alarms, the heater current will be measured when the

control output is ON, and the output will turn ON if the heater current is

lower than the set value (i.e., heater burnout detection current value).

For SSR failure alarms, the heater current will be measured when the

control output is OFF, and the output will turn ON if the heater current is

higher than the set value (i.e., SSR failure detection current value).

The value is 30 ms for a control period of 0.1 s or 0.2 s.

The value is 35 ms for a control period of 0.1 s or 0.2 s.

Electrical Life Expectancy Curve for

Control Output Relay (Reference Values)

Applicable OS

Windows XP/Vista/7/8

Applicable software

CX-Thermo version 4.62 or higher

Applicable models

@C-T Series, E5@C Series, and E5CB Series

USB interface standard Conforms to USB Specification 2.0

DTE speed

38,400 bps

Connector

specifications

Computer: USB (Type A plug)

Digital Temperature Controller: Special serial con-

nector

Power supply

Bus power (Supplied from the USB host controller) *

Power supply voltage

5 VDC

Current consumption

450 mA max.

Output voltage

4.7

±0.2 VDC (Supplied from USB-Serial Conver-

sion Cable to the Digital Temperature Controller.)

Output current

250 mA max. (Supplied from USB-Serial Conver-

sion Cable to the Digital Temperature Controller.)

Ambient operating

temperature

0 to 55

°C (with no condensation or icing)

Ambient operating

humidity

10% to 80%

Storage temperature

−20 to 60°C (with no condensation or icing)

Storage humidity

10% to 80%

Altitude

2,000 m max.

Weight

Approx. 120 g

Transmission line connection

method

RS-485: Multidrop

Communications

RS-485 (two-wire, half duplex)

Synchronization method

Start-stop synchronization

Protocol

CompoWay/F, or Modbus

Baud rate*

9,600, 19,200, 38,400, or 57,600 bps

Transmission code

ASCII

Data bit length *

7 or 8 bits

Stop bit length *

1 or 2 bits

Error detection

Vertical parity (none, even, odd)

Block check character (BCC)

with CompoWay/F or

CRC-16 with Modbus

Flow control

None

Interface

RS-485

Retry function

None

Communications buffer

217 bytes

Communications response

wait time

0 to 99 ms

Default: 20 ms

Programless

communica-

tions

You can use the memory in the PLC to read and write E5

parameters, start and stop operation, etc.

The E5

@C automatically performs communications with

PLCs. No communications programming is required.

Number of connected Digital Temperature Controllers: 32

max. (Up to 16 for the FX Series)

Applicable PLCs: OMRON PLCs

CS Series, CJ Series, or CP Series

Mitsubishi Electric PLCs

MELSEC Q Series, L Series, or FX Series (compati-

ble with the FX2 or FX3 (excluding the FX1S))

KEYENCE PLCs

KEYENCE KV Series

Component

Communica-

tions

When Digital Temperature Controllers are connected, set

points and RUN/STOP commands can be sent from the Dig-

ital Temperature Controller that is set as the master to the

Digital Temperature Controllers that are set as slaves.

Slope and offsets can be set for the set point.

Number of connected Digital Temperature Controllers: 32

max. (including master)

Copying*

When Digital Temperature Controllers are connected, the pa-

rameters can be copied from the Digital Temperature Control-

ler that is set as the master to the Digital Temperature

Controllers that are set as slaves.

Dielectric strength

1,000 VAC for 1 min

Vibration resistance

50 Hz, 98 m/s2

Weight

E54-CT1: Approx. 11.5 g,

E54-CT3: Approx. 50 g

Accessories (E54-CT3 only)

Armatures (2)

Plugs (2)

CT input (for heater current

detection)

Models with detection for single-phase heat-

ers: One input

Maximum heater current

50 A AC

Input current

indication accuracy

±5% FS ±1 digit max.

Heater burnout alarm

setting range *1

0.1 to 49.9 A (in units of 0.1 A)

Minimum detection ON time: 100 ms *3

SSR failure alarm setting

range *2

0.1 to 49.9 A (in units of 0.1 A)

Minimum detection OFF time: 100 ms *4

Switching current (A)

500

300

200

100

0.1

0.2

0.5

0.3

E5GC

250 VAC, 30 VDC

(resistive load)

cosφ = 1

E5DC-RX0ASM-015 数据表(PDF) 10 Page - Omron Electronics LLC

E5DC-RX0ASM-015 数据表(HTML) 10 Page - Omron Electronics LLC

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载