E5DC-RX2ASM-017 datasheet(31/138 Pages) OMRON

31 / 138 page

E5CC/E5CC-B/E5CC-U

E5CC-B (Push-In Plus Terminal Blocks)

Note: 1. The application of the terminals depends on the model.

2. Do not wire the terminals that are shown with a gray background.

3. When complying with EMC standards, the cable that connects the sensor must be 30 m or less.

If the cable length exceeds 30 m, compliance with EMC standards will not be possible.

4. Refer to Wiring Precautions for E5

@C-B (Controllers with Push-In Plus Terminal Blocks) on page 133 for wire specifications and wiring

methods.

5. Common terminals are indicated with asterisks (

*). You can use the input power supply and communications common terminals for

crossover wiring. Do not exceed the maximum number of Temperature Controllers given below if you use crossover wiring for the input

power supply.

100 to 240 VAC Controllers: 16 max.

24 VAC/VDC Controllers: 8 max.

6. Due to UL Listing requirements, use the E54-CT1L or E54-CT3L Current Transformer with the factory wiring (internal wiring). Use a UL

category XOBA or XOBA7 current transformer that is UL Listed for field wiring (external wiring) and not the factory wiring (internal wiring).

EV2

EV1

(-)

EV2

EV1

EV4

EV3

CT1

B(+)

A(-)

RS-485

B(+)

A(-)

RS-485

(no polarity)

100 to 240 VAC

24 VAC/DC

Auxiliary output 2

Auxiliary output 1

004

Communications

(RS-485), and

Event Inputs 3 and 4

006

Event Inputs

1 and 2, and

Transfer Output

001

Event Inputs 1

and 2, and CT1

002

Communications

(RS-485), CT1

(2) Auxiliary Outputs

(3) Input Power Supply

(5) Sensor (Temperature/Analog) Input

(6) Options

Relay outputs

outputs: 250 VAC, 2 A

(resistive load)

Auxiliary outputs 1, 2

(-)

Use no-voltage inputs for the event inputs.

The polarity for non-contact inputs is given in parentheses.

Transfer

Output

Models with

1 Relay Output

(1) Control output 1

Models with 1

Voltage Output

(for Driving SSR)

OUT1

−

Models with 1

Linear Current Output

OUT1

−

The E5CC is set for a K-type thermocouple

(input type = 5) by default. An input error

(

s.err) will occur if the input type setting does

not agree with the temperature sensor. Check

the input type.

E5CC-

@@ 2 @ B M - @@@

(1)

(2) (3) (4) (5)

(6)

↑

Terminal type

Control output 1

Relay output

250 VAC, 3A

(resistive load)

Voltage output

(for driving SSR)

12 VDC, 21 mA

To another E5

Wiring Example:

E5DC-RX2ASM-017 数据表(PDF) 31 Page - Omron Electronics LLC

E5DC-RX2ASM-017 数据表(HTML) 31 Page - Omron Electronics LLC

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载