NRF24L01P-R datasheet(23/78 Pages) NORDIC

23 / 78 page

Revision 1.0

Page 23 of 78

nRF24L01+ Product Specification

6.1.3.2

Standby-II mode

In standby-II mode extra clock buffers are active and more current is used compared to standby-I mode.

nRF24L01+ enters standby-II mode if CE is held high on a PTX device with an empty TX FIFO. If a new

packet is uploaded to the TX FIFO, the PLL immediately starts and the packet is transmitted after the nor-

mal PLL settling delay (130µs).

times see Table 16. on page 24.

6.1.4

RX mode

The RX mode is an active mode where the nRF24L01+ radio is used as a receiver. To enter this mode, the

nRF24L01+ must have the PWR_UP bit, PRIM_RX bit and the CE pin set high.

In RX mode the receiver demodulates the signals from the RF channel, constantly presenting the demodu-

lated data to the baseband protocol engine. The baseband protocol engine constantly searches for a valid

packet. If a valid packet is found (by a matching address and a valid CRC) the payload of the packet is pre-

sented in a vacant slot in the RX FIFOs. If the RX FIFOs are full, the received packet is discarded.

The nRF24L01+ remains in RX mode until the MCU configures it to standby-I mode or power down mode.

However, if the automatic protocol features (Enhanced ShockBurst™) in the baseband protocol engine are

enabled, the nRF24L01+ can enter other modes in order to execute the protocol.

In RX mode a Received Power Detector (RPD) signal is available. The RPD is a signal that is set high

when a RF signal higher than -64 dBm is detected inside the receiving frequency channel. The internal

RPD

signal is filtered before presented to the RPD register. The RF signal must be present for at least 40µs

before the RPD is set high. How to use the RPD is described in Section 6.4 on page 25.

6.1.5

TX mode

The TX mode is an active mode for transmitting packets. To enter this mode, the nRF24L01+ must have

the PWR_UP bit set high, PRIM_RX bit set low, a payload in the TX FIFO and a high pulse on the CE for

more than 10µs.

The nRF24L01+ stays in TX mode until it finishes transmitting a packet. If CE = 0, nRF24L01+ returns to

standby-I mode. If CE = 1, the status of the TX FIFO determines the next action. If the TX FIFO is not

empty the nRF24L01+ remains in TX mode and transmits the next packet. If the TX FIFO is empty the

nRF24L01+ goes into standby-II mode. The nRF24L01+ transmitter PLL operates in open loop when in TX

mode. It is important never to keep the nRF24L01+ in TX mode for more than 4ms at a time. If the

Enhanced ShockBurst™ features are enabled, nRF24L01+ is never in TX mode longer than 4ms.

NRF24L01P-R 数据表(PDF) 23 Page - Nordic Semiconductor

NRF24L01P-R 数据表(HTML) 23 Page - Nordic Semiconductor

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78

数据表下载