PIN FUNCTIONS (TQFP44)

Pin

Name

Description

1

N.C.

Not Connected.

2,3

transductor. The signal at this output can be the summ of:

- Internal Tone Generator,

- Sidetone signal.

4

N.C.

Not Connected.

5,6

- Receive Speech signal from DR,

- Internal Tone generator,

- Sidetone signal.

7

N.C.

Not Connected.

8

GNDP

together close to the device.

9

N.C.

Not Connected.

10

Receive data input: Data is shifted in during the assigned Received time slots In delayed and non-

delayed normal frame synchr. modes voice data byte is shifted in at the MCLK frequency on the

falling edges of MCLK, while in non-delayed reverse frame sinchr. mode voice data byte is shifted

in at the MCLK frequency on the rising edges of MCLK.

11,12,13

N.C.

Not Connected.

14

CCLK

Control Clock input: This clock shifts serial control information into CI and out from CO when the

CS- input is low, depending on the current instruction. CCLK may be asynchronous with the other

system clocks.

15

CS-

Chip Select input: When this pin is low, control information is written into and out from the ST5090

via CI and CO pins.

16

CI

Control data Input: Serial Control information is shifted into the ST5090 on this pin when CS- is low

on the rising edges of CCLK.

17

BZ

Pulse width modulated buzzer driver output.

18

Positive power supply input for the digital section. +5V

±10% or 3.3V ±10% selectable.

19

CO

Control data Output: Serial control/status information is shifted out from the ST5090 on this pin

when CS- is low on the falling edges of CCLK.

20

Transmit Data ouput: Data is shifted out on this pin during the assigned transmit time slots. Elsewhere

in non-delayed reverse frame synchr mode voice data byte is shifted out on the falling edge of MCLK.

21

GND

Ground: All digital signals are referenced to this pin.

22,23

N.C.

Not Connected.

24

FS

Frame Sync input: This signal is a 8kHz clock which defines the start of the transmit and receive

frames. Either of three formats may be used for this signal: non delayed normal mode, delayed

mode, and non delayed reverse mode.

25

MCLK

Master Clock Input: This signal is used by the switched capacitor filters and the encoder/decoder

sequencing logic. Values must be 512 kHz, 1.536 MHz, 2.048 MHz or 2.56 MHz selected by means of

Control Register CRO. MCLK is used also to shift-in and out data.

26

LO

A logic 1 written into DO (CR1) appears at LO pin as a logic 0

A logic 0 written into DO (CR1) appears at LO pin as a logic 1.

27,28,29

N.C.

Not Connected.

30

MIC2-

Second negative high impedance input to transmit pre-amplifier for microphone connection.

31

MIC2+

Second Positive high impedance input to transmit pre-amplifier for microphone connection.

32

N.C.

Not Connected.

33

MIC1-

Negative high impedance input to transmit pre-amplifier for microphone connection.

34

MIC1+

Positive high impedance input to transmit pre-amplifier for microphone connection.

35

N.C.

Not Connected.

36

GNDA

Analog Ground: All analog signals are referenced to this pin. GND and GNDA must be connected

together close to the device.

37

MIC3-

Third negative high impedance output to transmit preamplifier for microphone connection.

38

MIC3+

Third positive high impedance output to transmit preamplifier for microphone connection.

39,40

N.C.

Not Connected.

41

Positive power supply input for the analog section.

+5V

42

Positive power supply input for the power section. 5V

43,44

N.C.

Not Connected.

ST5090

4/29