ST72321 datasheet(137/185 Pages) STMICROELECTRONICS

137 / 185 page

ST72321

137/185

12.2 ABSOLUTE MAXIMUM RATINGS

Stresses above those listed as “absolute maxi-

mum ratings” may cause permanent damage to

the device. This is a stress rating only and func-

tional operation of the device under these condi-

tions is not implied. Exposure to maximum rating

conditions for extended periods may affect device

reliability.

12.2.1 Voltage Characteristics

12.2.2 Current Characteristics

Notes:

1. Directly connecting the RESET and I/O pins to VDD or VSS could damage the device if an unintentional internal reset

is generated or an unexpected change of the I/O configuration occurs (for example, due to a corrupted program counter).

To guarantee safe operation, this connection has to be done through a pull-up or pull-down resistor (typical: 4.7k

Ω for

RESET, 10k

Ω for I/Os). For the same reason, unused I/O pins must not be directly tied to V

DD or VSS.

2. When the current limitation is not possible, the VIN absolute maximum rating must be respected, otherwise refer to

IINJ(PIN) specification. A positive injection is induced by VIN>VDD while a negative injection is induced by VIN<VSS.

3. All power (VDD) and ground (VSS) lines must always be connected to the external supply.

4. Negative injection disturbs the analog performance of the device. See note in “ADC Accuracy” on page 167.

For best reliability, it is recommended to avoid negative injection of more than 1.6mA.

5. When several inputs are submitted to a current injection, the maximum

ΣI

INJ(PIN) is the absolute sum of the positive

and negative injected currents (instantaneous values). These results are based on characterisation with

ΣI

INJ(PIN) maxi-

mum current injection on four I/O port pins of the device.

6. True open drain I/O port pins do not accept positive injection.

Symbol

Ratings

Maximum value

Unit

VDD - VSS

Supply voltage

6.5

VPP - VSS

Programming Voltage

VIN

1) & 2)

Input Voltage on true open drain pin

VSS-0.3 to 6.5

Input voltage on any other pin

VSS-0.3 to VDD+0.3

∆V

DDx| and |∆VSSx|

Variations between different digital power pins

|VSSA - VSSx|

Variations between digital and analog ground pins

VESD(HBM)

Electro-static discharge voltage (Human Body Model)

see Section 12.7.3 on page 153

VESD(MM)

Electro-static discharge voltage (Machine Model)

Symbol

Ratings

Maximum value

Unit

IVDD

Total current into VDD power lines (source)

150

IVSS

Total current out of VSS ground lines (sink)

150

IIO

Output current sunk by any standard I/O and control pin

Output current sunk by any high sink I/O pin

Output current source by any I/Os and control pin

- 25

IINJ(PIN)

2) & 4)

Injected current on VPP pin

± 5

Injected current on RESET pin

± 2

Injected current on OSC1 and OSC2 pins

± 5

Injected current on any other pin 5) & 6)

± 5

ΣI

INJ(PIN)

Total injected current (sum of all I/O and control pins) 5)

± 25

ST72321 数据表(PDF) 137 Page - STMicroelectronics

ST72321 数据表(HTML) 137 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载