 |
数据搜索系统，热门电子元器件搜索 |
|
|
数据搜索系统，热门电子元器件搜索 |
|
ST7LITE02 数据表(PDF) 50 Page - STMicroelectronics |
|
|
|||||||||||||||||||||||||||||
ST7LITE02 数据表(HTML) 50 Page - STMicroelectronics |
|
|
50 / 122 page  ST7LITE0, ST7SUPERLITE 50/122 LITE TIMER (Cont’d) 11.1.6 Register Description LITE TIMER CONTROL/STATUS REGISTER (LTCSR) Read / Write Reset Value: 0x00 0000 (x0h) Bit 7 = ICIE Interrupt Enable. This bit is set and cleared by software. 0: Input Capture (IC) interrupt disabled 1: Input Capture (IC) interrupt enabled Bit 6 = ICF Input Capture Flag. This bit is set by hardware and cleared by software by reading the LTICR register. Writing to this bit does not change the bit value. 0: No input capture 1: An input capture has occurred Note: After an MCU reset, software must initialise the ICF bit by reading the LTICR register Bit 5 = TB Timebase period selection. This bit is set and cleared by software. 0: Timebase period = tOSC * 8000 (1ms @ 8 MHz) 1: Timebase period = tOSC * 16000 (2ms @ 8 MHz) Bit 4 = TBIE Timebase Interrupt enable. This bit is set and cleared by software. 0: Timebase (TB) interrupt disabled 1: Timebase (TB) interrupt enabled Bit 3 = TBF Timebase Interrupt Flag. This bit is set by hardware and cleared by software reading the LTCSR register. Writing to this bit has no effect. 0: No counter overflow 1: A counter overflow has occurred Bit 2 = WDGRF Force Reset/ Reset Status Flag This bit is used in two ways: it is set by software to force a watchdog reset. It is set by hardware when a watchdog reset occurs and cleared by hardware or by software. It is cleared by hardware only when an LVD reset occurs. It can be cleared by software after a read access to the LTCSR register. 0: No watchdog reset occurred. 1: Force a watchdog reset (write), or, a watchdog reset occurred (read). Bit 1 = WDGE Watchdog Enable This bit is set and cleared by software. 0: Watchdog disabled 1: Watchdog enabled Bit 0 = WDGD Watchdog Reset Delay This bit is set by software. It is cleared by hard- ware at the end of each tWDG period. 0: Watchdog reset not delayed 1: Watchdog reset delayed LITE TIMER INPUT CAPTURE REGISTER (LTICR) Read only Reset Value: 0000 0000 (00h) Bit 7:0 = ICR[7:0] Input Capture Value These bits are read by software and cleared by hardware after a reset. If the ICF bit in the LTCSR is cleared, the value of the 8-bit up-counter will be captured when a rising or falling edge occurs on the LTIC pin. Table 13. Lite Timer Register Map and Reset Values 70 ICIE ICF TB TBIE TBF WDGR WDGE WDGD 70 ICR7 ICR6 ICR5 ICR4 ICR3 ICR2 ICR1 ICR0 Address (Hex.) Register Label 7654 3210 0B LTCSR Reset Value ICIE 0 ICF x TB 0 TBIE 0 TBF 0 WDGRF 0 WDGE 0 WDGD 0 0C LTICR Reset Value ICR7 0 ICR6 0 ICR5 0 ICR4 0 ICR3 0 ICR2 0 ICR1 0 ICR0 0 1 |
|
链接网址 |
| ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 数据表链接 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
Chinese ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
