DG409LDY datasheet(5/12 Pages) VISHAY

5 / 12 page

Document Number: 71342

S-71241–Rev. E, 25-Jun-07

www.vishay.com

Vishay Siliconix

DG408L/409L

Notes:

a. Leakage parameters are guaranteed by worst case test condition and not subject to production test.

b. Room = 25 °C, Full = as determined by the operating temperature suffix.

c. The algebraic convention whereby the most negative value is a minimum and the most positive a maximum, is used in this data sheet.

d. Typical values are for DESIGN AID ONLY, not guaranteed nor subject to production testing.

e. Guaranteed by design, not subject to production test.

f. VIN = input voltage to perform proper function.

Δr

DS(on) = rDS(on) Max - rDS(on) Min.

h. Worst case isolation occurs on Channel 4 do to proximity to the drain pin.

i. rDS(on) flatness is measured as the difference between the minimum and maximum measured values across a defined Analog signal.

SPECIFICATIONS (SINGLE SUPPLY 5 V)

Parameter

Symbol

Test Conditions

Unless Otherwise Specified

V+ = 5 V, ± 10 %

, V- = 0 V

VEN = 0.6 V or 2.4 V

Tempb

Typd

A Suffix

- 55 to 125 °C

D Suffix

- 40 to 85 °C

Unit

Minc

Maxc

Minc

Maxc

Analog Switch

Analog Signal Rangee

VANALOG

Full

Drain-Source On-Resistance

rDS(on)

V+ = 4.5 V, VD or VS = 1 V or 3.5 V,

ID = 5 mA

Room

Full

rDS(on) Matching Between

Channelsg

Δr

V+ = 4.5 V, VD = 1 V or 3.5 V,

IS = 5 mA

Room

1.5

On-Resistance Flatnessi

rFLAT(on)

Room

Switch Off Leakage Currenta

IS(off)

V+ = 5.5 V, VS = 1 V or 4 V

VD = 4 V or 1 V

Room

Full

- 1

- 15

- 1

- 10

ID(off)

Room

Full

- 1

- 15

- 1

- 10

Channel On Leakage

Currenta

ID(on)

V+ = 5.5 V, VD = VS = 1 V or 4 V

Sequence Each Switch On

Room

Full

- 1

- 15

- 1

- 10

Digital Control

Logic High Input Voltage

VINH

V+ = 5 V

Full

2.4

Logic Low Input Voltage

VINL

Full

0.6

Input Currenta

IIN

VAX = VEN = 2.4 V or 0.6 V

Full

- 1.5

1.5

- 1

µA

Dynamic Characteristics

Transition Timee

tTRANS

VS1 = 3.5 V, VS8 = 0 V, (DG408L)

VS1b = 3.5 V, VS4b = 0 V, (DG409L)

See Figure 2

Room

Full

125

138

125

135

Break-Before-Make Timee

tOPEN

VS(all) = VDA = 3.5 V,

See Figure 4

Room

Full

Enable Turn-On Timee

tON(EN)

VAX = 0 V, VS1 = 3.5 V (DG408L)

VAX = 0 V, VS1b = 3.5 V (DG409L)

See Figure 3

Room

Full

Enable Turn-Off Timee

tOFF(EN)

Room

Full

Charge Injectione

CL = 1 nF, RGEN = 0 Ω, VGEN = 0 Ω

Room

Off Isolatione, h

OIRR

f = 100 kHz, RL = 1 kΩ

Room

- 70

Crosstalke

XTALK

Room

- 80

Source Off Capacitancee

CS(off)

f = 1 MHz, VS = 0 V, VEN = 0 V

Room

Drain Off Capacitancee

CD(off)

f = 1 MHz, VD = 0 V, VEN = 0 V

Room

Drain On Capacitancee

CD(on)

f = 1 MHz, VD = 0 V, VEN = 2.4 V

(DG409L only)

Room

DG409LDY 数据表(PDF) 5 Page - Vishay Siliconix

DG409LDY 数据表(HTML) 5 Page - Vishay Siliconix

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12

数据表下载

链接网址

DG409LDY 数据表(PDF) 5 Page - Vishay Siliconix

DG409LDY 数据表(HTML) 5 Page - Vishay Siliconix

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12

数据表 下载

链接网址

数据表下载