TAS3218IPZPR datasheet(39/79 Pages) TI

39 / 79 page

DSP Instruction Word

55-BIT INSTRUCTION

Ext

ALU First Stage

ALU Second Stage

Data Memory Load

Coefficient Memory Load

Memory Store

P1OP

53–49

P2OP

48–42

MOP1

AD1

41–37

36–27

MOP2

AD2

23–14

26–24

MOP3

AD3

9–0

13–10

TAS3218

www.ti.com ....................................................................................................................................................................................................... SLES235 – JULY 2008

The key features of the felay memory are

• 17408 24 delay memory locations

• Twenty four separately addressable pointers

• Programmable start/stop address on each pointer

• Pointers capable of accessing 24-bit or 48-bit words

• Single port access (one pointer access per access cycle)

• Access cycle < 4 DSP clocks

• Self clearing INIT pin used to clear all memory to zero

• Fully synchronous

• DP1DP15: sixteen 24-bit pointers

• RP1RP8: eight 48-bit (full precision) pointers

Since all of the pointers are contiguous, it is only necessary to write the address END point. For example, if DP1

is to be a three-sample delay, the register DP1 should be set to 0x003. If RP1 is to be a 3 sample delay, the

minimum of a one sample delay (one or two words).

DP1 Start address is defined as 000x0

DP2 Start address is equal to DP1 end address + 1 ...

RP1 Start address is equal to DP16 end address + 1 ...

RP8 Start address is equal to RP7 end address + 2

Since the start/stop address for each pointer is programmable anywhere in the delay RAMs address space, the

delay for any one channel can be anywhere in the delay RAM. There is, however, no address space collision

avoidance logic to separate the pointers. The user (or micro) must take care to avoid overlapping the address

spacing of each pointer.

Pointer register address endpoint registers DP1-DP16 and RP 1-RP8 are typically written only during the

initialization (fast load) mode of the device. Writing to these registers while the TAS3218 DSP core is accessing

the pointers may cause the pointers to cross the address space of another pointer.

To write to the delay RAM, the TAS3218 DSP core controller must present the data to be written on the

PT_DATA bus (LS bit always in bit zero of the bus), select the pointer to be accessed by driving the PT_SEL

pins, and assert the PT_WZ pin for a minimum of four clocks. The pointer will not increment until a write has

been performed and the PT_WZ pin has been de-asserted.

To perform a read, the PT_OUT bus may be read four clocks after PT_SEL is driven.

TAS3218 has a 55-bit instruction word. Each instruction has five independent operations, which can load two

operands from data memory and coefficient memory, store the result into data or coefficient memory and perform

two parallel arithmetic operations.

Figure 30. Instruction Word

The TAS3218 instruction set is a superset of the TAS3218 instruction set, extending the DSP processing

capabilities for improved efficiency of FIR operations as well as extending the addressable memory space. The

Ext instruction bit (bit 54) has been added to extend the internal memory address space by 1 bit, increasing the

memory space from 1K to 2K words.

Submit Documentation Feedback

Product Folder Link(s): TAS3218

TAS3218IPZPR 数据表(PDF) 39 Page - Texas Instruments

TAS3218IPZPR 数据表(HTML) 39 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79

数据表下载