Document Number: 31514

For technical questions, contact: ff2aresistors@vishay.com

www.vishay.com

Revision: 25-Jul-08

4

MSM (Military M83401)

Thick Film Resistor Networks Military, MIL-PRF-83401 Qualified,

Type RZ, Single-In-Line, Molded SIP; 01, 03, 05 Schematics

Vishay Dale

CIRCUIT APPLICATIONS

01 Schematic

5, 7 or 9 resistors with one pin common

“A” Profile

“C” Profile

MSM06A01 (M8340107xxxxxxC)

MSM06C01 (M8340104xxxxxxC)

MSM08A01 (M8340108xxxxxxC)

MSM08C01 (M8340105xxxxxxC)

MSM10A01 (M8340109xxxxxxC)

MSM10C01 (M8340106xxxxxxC)

The MSM06A01, MSM08A01, MSM10A01, MSM06C01, MSM08C01 and

MSM10C01 molded single-in-line resistor networks provide the user with a

choice of 5, 7 or 9 nominally equal resistors, each connected to a common

pin (Pin No. 1).

Commonly used in the following applications:

• “Wired OR” Pull-up

• Open Collector Pull-up

• Power Gate Pull-up

• TTL Input Pull-down

• MOS/ROM Pull-up/Pull-down

• TTL Unused Gate Pull-up

03 Schematic

3, 4 or 5 isolated resistors

“A” Profile

“C” Profile

MSM06A03 (M8340107xxxxxxG)

MSM06C03 (M8340104xxxxxxG)

MSM08A03 (M8340108xxxxxxG)

MSM08C03 (M8340105xxxxxxG)

MSM10A03 (M8340109xxxxxxG)

MSM10C03 (M8340106xxxxxxG)

The MSM06A03, MSM08A03, MSM10A03, MSM06C03, MSM08C03 and

MSM10C03 molded single-in-line resistor networks provide the user with a

choice of 3, 4 or 5 nominally equal resistors. Each resistor is isolated from all

others.

Commonly used in the following applications:

• “Wired OR” Pull-up

• Long-Line Impedance Balance

• Power Driven Pull-up

• LED Current Limiting

• Power Gate Pull-up

• ECL Output Pull-down

• Line Termination

• TTL Input Pull-down

05 Schematic

4, 6 or 8 isolated resistors

“A” Profile

“C” Profile

MSM06A05 (M8340107xxxxxxH)

MSM06C05 (M8340104xxxxxxH)

MSM08A05 (M8340108xxxxxxH)

MSM08C05 (M8340105xxxxxxH)

MSM10A05 (M8340109xxxxxxH)

MSM10C05 (M8340106xxxxxxH)

The MSM06A05, MSM08A05, MSM10A05, MSM06C05, MSM08C05

and MSM10C05 molded single-in-line resistor networks provide the

user with a choice of 4, 6 or 8 pair of R1/R2 resistor values for pulse

squaring and TTL dual-line terminating requirements.

PERFORMANCE

TEST

CONDITIONS

MAX.

ΔR (Typical Test Lots)

Power Conditioning

1.5 x rated power, applied 1.5 h “ON” and 0.5 h “OFF” for 100 h ± 4 h

at + 25 °C ambient temperature

± 0.50 %

ΔR

Thermal Shock

5 cycles between - 65 °C and + 125 °C

± 0.50 %

ΔR

Short Time Overload

2.5 x rated working voltage for 5 s

± 0.25 %

ΔR (Characteristic K)

± 0.50 %

ΔR (Characteristic M)

Low Temperature Operation

45 min at full rated working voltage at - 65 °C

± 0.25 %

ΔR (Characteristic K)

± 0.50 %

ΔR (Characteristic M)

Moisture Resistance

240 h with humidity ranging from 80 % RH to 98 % RH

± 0.50 %

ΔR

Resistance to Soldering Heat

Leads immersed in + 260 °C solder to within 1/16" of body for 10 s

± 0.25 %

ΔR

Shock

Total of 18 shocks at 100 G's

± 0.25 %

ΔR

Vibration

12 h at maximum of 20 G's between 10 and 2000 Hz

± 0.25 %

ΔR

Load Life

1000 h at + 70 °C, rated power applied 1.5 h “ON”,

0.5 h “OFF” for full 1000 h period

± 0.50 %

ΔR (Characteristic K)

± 2.00 %

ΔR (Characteristic M)

Terminal Strength

4 1/2 pound pull for 30 s

± 0.25 %

ΔR

Insulation Resistance

10 000 M

Ω (minimum)

-

Dielectric Withstanding

-

1

2

3

n-1

n

1

2 3

4

n-1

n

1

2

3

n-1

n

R

2

R

1