| 数据搜索系统,热门电子元器件搜索 |
|
TSM109D 数据表(PDF) 3 Page - STMicroelectronics |
|
|
|||||||||||||||||||||||||||||
TSM109D 数据表(HTML) 3 Page - STMicroelectronics |
|
3 / 7 page ![]() TSM109/A 3/7 ELECTRICAL CHARACTERISTICS COMPARATOR (independent comparator) VCC+ = +5V, VCC -= GND, T amb = +25°C (unless otherwise specified) Symbol Parameter TSM109 Unit Min. Typ. Max. Vio Input Offset Voltage - note 1) Tamb = +25°C Tmin ≤ Tamb ≤ Tmax 1. At output switch point, Vo ≈ 1.4V, Rs = 0 with VCC + from 5V to 30V, and over the full common-mode range (0V to V CC + -1.5V). 15 9 mV Iio Input Offset Current Tamb = +25°C Tmin ≤ Tamb ≤ Tmax 325 100 nA Iib Input Bias Current (I+ or I-) - note 2) Tamb = +25°C Tmin ≤ Tamb ≤ Tmax 2. The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent of the state of the output, so no loading charge exists on the reference of input lines. 25 250 400 nA Avd Large Signal Voltage Gain VCC = 15V, RL = 15kΩ, Vo = 1V to 11V 50 200 V/mV Vicm Input Common Mode Voltage Range - note 3) VCC = 30V Tamb = +25°C Tmin ≤ Tamb ≤ Tmax 3. The input common-mode voltage of either input signal voltage should not be allowed to go negative by more than 0.3V. The upper end of the common-mode voltage range is VCC + -1.5V, but either or both inputs can go to +30V without damage. 0 0 VCC + -1.5 VCC + -2 V Vid Differential Input Voltage -note 4) 4. Positive voltage excursions of one input may exceed the power supply level. As long as the other input voltage remains within the common-mode range, the comparator will provide an appropriate output state. The low input voltage state must not be less than -0.3V (or 0.3V below the negative power supply, if used). VCC + VOL Low Level Output Voltage Vid = -1V, Isink = 4mA Tamb = +25°C Tmin ≤ Tamb ≤ Tmax 250 400 700 mV IOH High Level Output Current (Vid = 1V) VCC = Vo = 30V Tamb = +25°C Tmin ≤ Tamb ≤ Tmax 30 150 1 nA µA Isink Output Sink Currrent Vid= 1V, Vo = 1.5V 10 20 mA tre Response Time - note 5) RL= 5.1kΩ connected to VCC + 5. The response time specified is for a 100mV input step with 5mV overdrive. For larger overdrive signals, 300ns can be obtained 1.3 µs trel Large Signal Response Time RL= 5.1kΩ connected to VCC +, e l = TTL, V(ref) = +1.4v 300 ns |
|
|
链接网址 |
| ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 数据表链接 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |