CS5467 datasheet(20/46 Pages) CIRRUS

20 / 46 page

CS5467

DS714F1

6. SETTING UP THE CS5467

6.1 Clock Divider

The internal clock to the CS5467 needs to operate

around 4 MHz. However, by using the internal clock di-

vider, a higher crystal frequency can be used. This is im-

portant

when

driving

external

microcontroller

requiring a faster clock and using the CPUCLK output.

K is the divide ratio from the crystal input to the internal

clock and is selected with Configuration register (Con-

fig

) bits K[3:0]. It has a range of 1 to 16. A value of zero

results in a setting of 16.

6.2 CPU Clock Inversion

By default, CPUCLK is inverted from XIN. Setting Con-

figuration register bit iCPU removes this inversion. This

can be useful when one phase adds more noise to the

system than the other.

6.3 Interrupt Pin Behavior

The behavior of the INT pin is controlled by the IMODE

and IINV bits in the Configuration register as shown.

If IMODE = 1, the duration of the INT pulse will be two

DCLK cycles, where DCLK = MCLK/K.

6.4 Current Input Gain Ranges

Control register bits I1gain (I2gain) select the input

range of the current inputs.

6.5 High-pass Filters

Mode Control (Modes) register bits VHPF and IHPF ac-

tivate the HPF in the voltage and current paths, respec-

tively. Each energy channel has separate VHPF and

IHPF bits. When a high-pass filter is enabled in only one

path within a channel, a phase matching filter (PMF) is

applied to the other path within that channel. The PMF

filter matches the amplitude and phase response of the

HPF in the band of interest, but passes DC.

6.6 Cycle Count

Low-rate calculations, such as average power and RMS

voltage and current integrate over several (N) output

word rate (OWR) samples. The duration of this averag-

ing window is set by the Cycle Count (N) register. By de-

fault, Cycle Count is set to 4000 (1 second at output

word rate [OWR] of 4000 Hz). The minimum value for

Cycle Count is 10.

6.7 Energy Pulse Outputs

By default, E1 outputs total active energy, E3, total re-

active energy, and E2, the sign of both active and reac-

tive energy. (See Figure 2. Timing Diagram for E1, E2,

and E3

on page 13.)

Three pairs of bits in the Mode Control (Modes) register

control the operation of these outputs. These bits are

named

E1MODE[1:0],

E2MODE[1:0],

and

E3MODE[1:0]. Some combinations of these bits over-

ride others, so read the following paragraphs carefully.

The E2 pin can output energy sign, or total apparent en-

ergy. Table 4 lists the functions of E2 as controlled by

E2MODE[1:0] in the Modes register.

Note: E2MODE[1:0]=3 is a special mode.

The E3 pin can output total reactive energy, power fail

monitor status, voltage1 sign, or total apparent energy.

Table 5 lists the functions of E3 as controlled by

IMODE

IINV

INT Pin

Active-low Level

Active-high Level

Low Pulse

High Pulse

Table 1. Interrupt Configuration

I1gain, I2gain

Maximum Input

Gain

0±250 mV

10x

±50 mV

50x

Table 2. Current Input Gain Ranges

VHPF

IHPF

Filter Configuration

No filter on Voltage or Current

HPF on Current, PMF on Voltage

HPF on Voltage, PMF on Current

HPF on Current and Voltage

Table 3. High-pass Filter Configuration

E2MODE1 E2MODE0

E2 output

Energy Sign

Total Apparent Energy

Not Used

Enable E1MODE

Table 4. E2 Pin Configuration

CS5467 数据表(PDF) 20 Page - Cirrus Logic

CS5467 数据表(HTML) 20 Page - Cirrus Logic

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46

数据表下载