20

LT1078/LT1079

10789fe

LT/CPI 1201 1.5K REV E • PRINTED IN USA

©LINEAR TECHNOLOGY CORPORATION 1994

S8 Package

8-Lead Plastic Small Outline (Narrow .150 Inch)

(Reference LTC DWG # 05-08-1610)

SW Package

16-Lead Plastic Small Outline (Wide .300 Inch)

(Reference LTC DWG # 05-08-1620)

N Package

14-Lead PDIP (Narrow .300 Inch)

(Reference LTC DWG # 05-08-1510)

Linear Technology Corporation

1630 McCarthy Blvd., Milpitas, CA 95035-7417

N14 1098

0.020

(0.508)

MIN

0.125

(3.175)

MIN

0.130

± 0.005

(3.302

± 0.127)

0.045 – 0.065

(1.143 – 1.651)

0.065

(1.651)

TYP

0.018

± 0.003

(0.457

± 0.076)

0.100

(2.54)

BSC

0.005

(0.125)

MIN

0.009 – 0.015

(0.229 – 0.381)

0.300 – 0.325

(7.620 – 8.255)

0.325

+0.035

–0.015

+0.889

–0.381

8.255

()

0.255

± 0.015*

(6.477

± 0.381)

0.770*

(19.558)

MAX

3

1

2

4

5

6

7

8

9

10

11

12

13

14

*THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS.

MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.010 INCH (0.254mm)

0.016 – 0.050

(0.406 – 1.270)

0.010 – 0.020

(0.254 – 0.508)

× 45°

0

°– 8° TYP

0.008 – 0.010

(0.203 – 0.254)

SO8 1298

0.053 – 0.069

(1.346 – 1.752)

0.014 – 0.019

(0.355 – 0.483)

TYP

0.004 – 0.010

(0.101 – 0.254)

0.050

(1.270)

BSC

1

2

3

4

0.150 – 0.157**

(3.810 – 3.988)

8

7

6

5

0.189 – 0.197*

(4.801 – 5.004)

0.228 – 0.244

(5.791 – 6.197)

DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH

SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE

DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD

FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE

*

**

S16 (WIDE) 1098

NOTE 1

0.398 – 0.413*

(10.109 – 10.490)

16

15

14

13

12

11

10

9

1

23

4

5

6

78

0.394 – 0.419

(10.007 – 10.643)

0.037 – 0.045

(0.940 – 1.143)

0.004 – 0.012

(0.102 – 0.305)

0.093 – 0.104

(2.362 – 2.642)

0.050

(1.270)

BSC

0.014 – 0.019

(0.356 – 0.482)

TYP

0

° – 8° TYP

NOTE 1

0.009 – 0.013

(0.229 – 0.330)

0.016 – 0.050

(0.406 – 1.270)

0.291 – 0.299**

(7.391 – 7.595)

× 45°

0.010 – 0.029

(0.254 – 0.737)

NOTE:

1. PIN 1 IDENT, NOTCH ON TOP AND CAVITIES ON THE BOTTOM OF PACKAGES ARE THE MANUFACTURING OPTIONS.

THE PART MAY BE SUPPLIED WITH OR WITHOUT ANY OF THE OPTIONS

DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE

DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE

*

**