LTC3544BEUD datasheet(3/16 Pages) LINER

3 / 16 page

LTC3544B

3544bfa

Note 1: Stresses beyond those listed under Absolute Maximum Ratings

may cause permanent damage to the device. Exposure to any Absolute

Maximum Rating condition for extended periods may affect device

reliability and lifetime.

Note 2: The LTC3544BE is guaranteed to meet performance speciﬁcations

from 0°C to 85°C. Speciﬁcations over the –40°C to 85°C operating

temperature range are assured by design, characterization and correlation

with statistical process controls.

Note 3: TJ is calculated from the ambient temperature TA and power

dissipation PD according to the following formula:

TJ = TA + (PD)(68°C/W).

SYMBOL

PARAMETER

CONDITIONS

MIN

TYP

MAX

UNITS

VRUN(HIGH)

RUNx Input High Voltage

●

1.0

VRUN(LOW)

RUNx Input Low Voltage

●

0.3

ILSW

SWx Leakage

VRUN = 0V, VSW = 0V or 5.5V, VIN = 5.5V

±0.1

±1

μA

IRUN

RUN Leakage Current

VIN = 5.5V

●

±0.1

±1

μA

IVFB

VFBx Leakage Current

tSS

Soft-Start Period

VFB = 7.5% to 92.5% Full Scale

650

875

1200

μs

VUVLO

Undervoltage Lockout

●

1.9

2.25

Individual Regulator Characteristics

Regulator SW300 – 300mA

IPK

Peak Switch Current Limit

VFB < VFBREG, Duty Cycle < 35%

400

600

800

IS300

Input DC Bias Current–Reg SW300 Only

Active Mode (Pulse Skip)

VFB = 0.7V, ILOAD = 0A, 2.25MHz

320

μA

RPFET

RDS(ON) of P-Channel FET (Note 7)

ISW = 100mA

0.55

RNFET

RDS(ON) of N-Channel FET (Note 7)

ISW = –100mA

0.50

Regulator SW200A – 200mA

IPK

Peak Switch Current Limit

VFB < VFBREG, Duty Cycle < 35%

300

400

500

IS200

Input DC Bias Current–Reg SW200A Only

Active Mode (Pulse Skip)

VFB = 0.7V, ILOAD = 0A, 2.25MHz

320

μA

RPFET

RDS(ON) of P-Channel FET (Note 7)

ISW = 100mA

0.65

RNFET

RDS(ON) of N-Channel FET (Note 7)

ISW = –100mA

0.60

Regulator SW200B – 200mA

IPK

Peak Switch Current Limit

VFB < VFBREG, Duty Cycle < 35%

300

400

500

IS200

Input DC Bias Current–Reg SW200B Only

Active Mode (Pulse Skip)

VFB = 0.7V, ILOAD = 0A, 2.25MHz

320

μA

RPFET

RDS(ON) of P-Channel FET (Note 7)

ISW = 100mA

0.65

RNFET

RDS(ON) of N-Channel FET (Note 7)

ISW = –100mA

0.60

Regulator SW100 – 100mA

IPK

Peak Switch Current Limit

VFB < VFBREG, Duty Cycle < 35%

200

300

400

IS100

Input DC Bias Current–Reg SW100B Only

Active Mode (Pulse Skip)

VFB = 0.7V, ILOAD = 0A, 2.25MHz

320

μA

RPFET

RDS(ON) of P-Channel FET (Note 7)

ISW = 100mA

0.80

RNFET

RDS(ON) of N-Channel FET (Note 7)

ISW = –100mA

0.75

ELECTRICAL CHARACTERISTICS The ● denotes the speciﬁcations which apply over the full operating

temperature range, otherwise speciﬁcations are at TA = 25°C. VIN = 3.6V unless otherwise noted.

Note 4: This IC includes overtemperature protection that is intended

to protect the device during momentary overload conditions. Junction

temperature will exceed 125°C when overtemperature is active.

Continuous operation above the speciﬁed maximum operating junction

temperature may impair device reliability.

Note 5: The LTC3544B is tested in a proprietary test mode that connects

VFB to the output of the error ampliﬁer.

Note 6: Load regulation is inferred by measuring the regulation loop gain.

Note 7: The QFN switch on-resistance is guaranteed by correlation to

wafer level measurements.

Note 8: Guaranteed by long-term current density limitations.

LTC3544BEUD 数据表(PDF) 3 Page - Linear Technology

LTC3544BEUD 数据表(HTML) 3 Page - Linear Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

数据表下载

链接网址

LTC3544BEUD 数据表(PDF) 3 Page - Linear Technology

LTC3544BEUD 数据表(HTML) 3 Page - Linear Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

数据表 下载

链接网址

数据表下载