CY74FCT16827ATPVC datasheet(2/7 Pages) TI

2 / 7 page

CY74FCT16827T

CY74FCT162827T

Maximum Ratings[2, 3]

(Above which the useful life may be impaired. For user

guidelines, not tested.)

Storage Temperature ...............................

−55°C to +125°C

Ambient Temperature with

Power Applied..........................................

−55°C to +125°C

DC Input Voltage

.................................................−0.5V to +7.0V

DC Output Voltage

..............................................−0.5V to +7.0V

DC Output Current

(Maximum Sink Current/Pin)

...........................−60 to +120 mA

Power Dissipation .......................................................... 1.0W

Static Discharge Voltage............................................>2001V

(per MIL-STD-883, Method 3015)

Pin Description

Name

Description

Output Enable Inputs (Active LOW)

Data Inputs

Three-State Outputs

Function Table[1]

Inputs

Outputs

OE1

OE2

Operating Range

Range

Ambient

Temperature

VCC

Industrial

−40°C to +85°C

± 10%

Electrical Characteristics Over the Operating Range

Parameter

Description

Test Conditions

Min.

Typ.[4]

Max.

Unit

VIH

Input HIGH Voltage

2.0

VIL

Input LOW Voltage

0.8

Input Hysteresis[5]

100

VIK

Input Clamp Diode Voltage

VCC=Min., IIN=−18 mA

−0.7

−1.2

IIH

Input HIGH Current

VCC=Max., VI=VCC

±1

µA

IIL

Input LOW Current

VCC=Max., VI=GND

±1

µA

IOZH

High Impedance Output

Current (Three-State Output pins)

VCC=Max., VOUT=2.7V

±1

µA

IOZL

High Impedance Output

Current (Three-State Output pins)

VCC=Max., VOUT=0.5V

±1

µA

IOS

Short Circuit Current[6]

VCC=Max., VOUT=GND

−80

−140

−200

Output Drive Current[6]

VCC=Max., VOUT=2.5V

−50

−180

IOFF

Power-Off Disable

VCC=0V, VOUT≤4.5V

[7]

±1

µA

Output Drive Characteristics for CY74FCT16827T

Parameter

Description

Test Conditions

Min.

Typ.[4]

Max.

Unit

VOH

Output HIGH Voltage

VCC=Min., IOH=−3 mA

2.5

3.5

VCC=Min., IOH=−15 mA

2.4

3.5

VCC=Min., IOH=−32 mA

2.0

3.0

VOL

Output LOW Voltage

VCC=Min., IOL=64 mA

0.2

0.55

H = HIGH Voltage Level. L = LOW Voltage Level. X = Don’t Care.Z = HIGH Impedance.

Operation beyond the limits set forth may impair the useful life of the device. Unless noted, these limits are over the operating free-air temperature range.

Unused inputs must always be connected to an appropriate logic voltage level, preferably either VCC or ground.

Typical values are at VCC= 5.0V, TA= +25˚C ambient.

This parameter is speciﬁed but not tested.

Not more than one output should be shorted at a time. Duration of short should not exceed one second. The use of high-speed test apparatus and/or sample

and hold techniques are preferable in order to minimize internal chip heating and more accurately reﬂect operational values. Otherwise prolonged shorting of

a high output may raise the chip temperature well above normal and thereby cause invalid readings in other parametric tests. In any sequence of parameter

tests, IOS tests should be performed last.

Tested at +25˚C.

CY74FCT16827ATPVC 数据表(PDF) 2 Page - Texas Instruments

CY74FCT16827ATPVC 数据表(HTML) 2 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7

数据表下载

链接网址

CY74FCT16827ATPVC 数据表(PDF) 2 Page - Texas Instruments

CY74FCT16827ATPVC 数据表(HTML) 2 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7

数据表 下载

链接网址

数据表下载