MB Series Motor Bells CS-2236 05/04/04

Page 2 of 2

Specifications and wiring information are provided for information only and are believed

to be accurate. Gamewell assumes no responsibility for their use.

Data and design are subject to change without notice. Installation and wiring

instructions shipped with the product shall always be used for actual installation. For

more information, contact Gamewell.

The Gamewell Company

12 Clintonville Road

Northford, CT 06472-1610

Phone: 203-484-7161

Fax: 203-484-7118

www.gamewell.com

A Honeywell Company

© 2004 Gamewell

Ordering Information

Wiring Diagram

NOTES:

1. Typical dBA at 10 feet is 92, measured in an

anechoic chamber.

2.Mounting options are: D,E,J,K,N,R,S,Z

3. For bells at 12 VDC models are UL rated for 9.0 to

15.6 VDC and all 24 VDC models for 18.0 to 31.0

Fig. 1 Bell Models

Fig. 2 Retrofit Strobe

+-

{}

TO NEXT

APPLIANCE

OR END-OF-LINE

RESISTOR

(EO LR)

FRO M

PRECEDING

APPLIANCE

OR FACP

TO NEXT

APPLIANCE

OR EOLR

FROM

PRECEDING

APPLIANCE OR

FACP

TO NEXT

ST ROBE OR

EOLR

FROM

PRECEDING

STROBE OR

FACP

AUDIBLE

STROBE

+

-

-

+

+

-

--

-

++

+

MODEL

NUMBER

SHELL

SIZE

INPUT

VOLTAGE

(VDC)

INPUT

CURRENT

MB-G6-12-R

6"

12

0.060

MB-G6-24-R

6"

24

0.030

MB-G10-12-R

10"

12

0.060

MB-G10-24-R

10"

24

0.030

MODEL

NUMBER

NOMINAL

VOLTAGE

(VDC)

STROBE

CANDELA

AVERAGE CURRENT

(amps) @ LISTED

VDC

RSSP-24MCW-FR

24

15/30/75/110

.050/.081/.133/.161

RSSP-241575W-FR

24

15 (75 on axis)

0.065

RSSP-121575W-FR

12

15 (75 on axis)

0.170

1. Mounting options are: D,E,Z

2. Average current per actual Wheelock product testing at listed VDC.

For rated average and peak current across UL regulated voltage range

for both filtered DC and unfiltered VRMS, see Installation instructions.

SM Sync Module is rated for 3.0 amperes @ 24VDC.

DSM Sync Module is rated for 3.0 amperes per circuit. The maximum number of

interconnected DSM modules is twenty (20).

** Refer to mounting options data sheet.

Wheelock products must be used within their published specifications and must be PROPERLY specified, applied, installed,

operated, maintained and operationally tested in accordance with their installation instructions at the time of installation and at

least twice a year or more often and in accordance with local, state and federal codes, regulations and laws. Specification,

application, installation, operation, maintenance and testing must be performed by qualified personnel for proper operation in

accordance with all of the latest National Fire Protection Association (NFPA), Underwriters’ Laboratories (UL), National Electrical

Code (NEC), Occupational Safety and Health Administration (OSHA), local, state, county, province, district, federal and other

applicable building and fire standards, guidelines, regulations, laws and codes including, but not limited to, all appendices and

amendments and the requirements of the local authority having jurisdiction (AHJ).

WARNING

PLEASE READ THESE SPECIFICATIONS AND ASSOCIATED INSTALLATION INSTRUCTIONS

CAREFULLY BEFORE USING, SPECIFYING OR APPLYING THIS PRODUCT. FAILURE TO COM-

PLY WITH ANY OF THESE INSTRUCTIONS, CAUTIONS OR WARNINGS COULD RESULT IN

IMPROPER APPLICATION, INSTALLATION AND/OR OPERATION OF THESE PRODUCTS IN AN

EMERGENCY SITUATION, WHICH COULD RESULT IN PROPERTY DAMAGE, AND SERIOUS

INJURY OR DEATH TO YOU AND/OR OTHERS.

MODEL

NUM BER

INP UT

VOLTAGE

(VDC)

AVERAGE

MEAN

CURRENT

@ 24 VDC

MOUNTING

OP TIONS**

SM-12/24-R

24

.028

W

DSM-12/24-R

24

.035

W

SYNC MODELS/POWER SUPPLY