Flex 404 Four-Zone FACP

CS-2404

09/01/06

Page 2 of 2

Specifications and wiring information are provided for information only and are

believed to be accurate. Gamewell-FCI assumes no responsibility for their use.

Data and design are subject to change without notice. Installation and wiring

instructions shipped with the product shall always be used for actual installation. For

more information, contact Gamewell-FCI.

Gamewell-FCI

12 Clintonville Road

Northford, CT 06472-1610

Phone: 203-484-7161

Fax: 203-484-7118

www.gamewell-fci.com

A Honeywell Company

© 2006 Gamewell-FCI

Specifications

AC power, TB8

120 VAC, 50/60 Hz, 2.3 A.

Wire size: minimum 14 AWG (2.0 mm²) with

600 V insulation.

Battery (sealed lead-acid only), J8

Maximum charging circuit: normal flat charge

27.6 VDC @ 0.8 A.

Maximum battery charger capacity:

18 AH battery. Two 7 AH batteries can be

housed in the FACPcabinet.Larger batteries

require a separate battery box i.e. BB-17F.

Initiating device circuits, TB3

Alarm zones 1 – 4. Power-limited circuitry.

Operation: all zones Style B (Class B).

Normal operating voltage: nominal 22 VDC.

Alarm current: 15 mA minimum.

Standby current: 4 mA.

Short circuit current: 40 mA maximum.

Maximum loop resistance: 100 ohms. End-

of-line resistor: 4.7K ohm, 1/2 watt (P/N

71252).

Notification appliance circuits, TB2

Two NACs on Flex 404. Power-limited

circuitry.

Normal operating voltage: nominal 24 VDC.

Maximum signaling current: 2.5 A total with

standard transformer; 5.0 Atotal (2.5

maximum per NAC) with optional trans-

former.

End-of-line resistor: 4.7K ohm, 1/2 watt

(P/N 71252).

Form-C relays

Trouble relay TB5 (fail-safe). Alarm relayTB6.

Contact ratings: 2.0 A @ 30 VAC (resistive).

Auxiliary outputs

Resettable power, TB1

Power-limiting circuitry.

Operating voltage: nominal 24 VDC.

Maximum available current: 500 mA,

appropriate for powering four-wire smoke

detectors. See note under nonresettable.

Nonresettable power, TB1

Power-limiting circuitry.

Operating voltage: nominal 24 VDC.

Maximum available current: 500 mA,

appropriateforpoweringfour-wiresmoke

detectors.Note:Totalcurrentfornonre-settable

power, resettable power and two NACs must

not exceed 6A for the Flex 404.

Cabinet dimensions

Door: 15.342" (38.97 cm) high x 14.677"

(37.28 cm) wide x 0.375" (0.95 cm) deep.

Backbox: 15.0" (38.10 cm) high x 14.5"

(36.83 cm) wide x 3.0" (7.62 cm) deep.

Backbox Mounting

The cabinet can be surface-mounted. The door is removable during installation

by opening and lifting it off the hinges. The cabinet mounts using two key slots at

the top of the backbox and two additional 0.250" diameter holes at the bottom.

Ordering Information

F404

Four-zone conventional FACP.

XRM-24

120 VAC, 100 VA transformer, expands NAC power from 3.0

to 5.0 Amps.

CAC-4

Class A converter module. Used to convert Style B (Class

B) IDC to Style D (Class A) and Style Y (Class B) NAC to

Style Z (Class A). The module connects to J1 on the Flex

404 circuit board.

4XTMF

Transmitter module.

4XLMF

LED interface module, supports SAN-404.

4XZMF

Zone relay module.

411UD

Four-input (channel) 411UD dual-line Digital Alarm Commu-

nicator/Transmitters, which can be used as slave communi-

cators with Flex 404.

PRO-411

Programmer used with 411UD.

SAN-404

Remote annunciator (RZA-4XF), mounts in a single-gang

box.

BB-17F

Battery box, required to house two batteries greater than 7

AH, to a maximum of 18 AH.

DP-FLEX

Dress panel.

TR-1-R

Trim ring for semi-flush mounting.

52194

Flex 404 Installation and Maintenance Manual.

i³™ is a trademark and Gamewell® is a registered trademark of Honeywell International Inc.