Notes:

the side of the unit

Model

Number

Input

Output

Load

Regulation

(%, Max)

Efficiency

(%, Typ)

Fuse Rating

Slow-Blow

(mA)

Voltage (VDC)

Current (mA)

Voltage

(VDC)

Current

(mA, Max)

Current

(mA, Min)

Nominal

Range

Full-Load

No-Load

D101

5

4.5 - 5.5

267

30

3.3

303.0

6.0

10

75

500

D102

5

4.5 - 5.5

256

30

5.0

200.0

4.0

10

78

500

D103

5

4.5 - 5.5

267

30

9.0

111.0

2.2

10

75

500

D104

5

4.5 - 5.5

263

30

12.0

83.3

1.6

10

76

500

D105

5

4.5 - 5.5

263

30

15.0

66.6

1.3

10

76

500

D106

5

4.5 - 5.5

270

30

±5.0

±100.0

±2.0

10

74

500

D107

5

4.5 - 5.5

256

30

±9.0

±55.5

±1.1

10

78

500

D108

5

4.5 - 5.5

256

30

±12.0

±41.6

±0.8

10

78

500

D109

5

4.5 - 5.5

250

30

±15.0

±33.3

±0.6

10

80

500

D111

12

10.8 - 13.2

113

20

3.3

303.0

6.0

10

74

200

D112

12

10.8 - 13.2

113

20

5.0

200.0

4.0

10

74

200

D113

12

10.8 - 13.2

111

20

9.0

111.0

2.2

10

75

200

D114

12

10.8 - 13.2

108

20

12.0

83.3

1.6

10

77

200

D115

12

10.8 - 13.2

106

20

15.0

66.6

1.3

10

78

200

D116

12

10.8 - 13.2

111

20

±5.0

±100.0

±2.0

10

75

200

D117

12

10.8 - 13.2

109

20

±9.0

±55.5

±1.1

10

76

200

D118

12

10.8 - 13.2

106

20

±12.0

±41.6

±0.8

10

78

200

D119

12

10.8 - 13.2

104

20

±15.0

±33.3

±0.6

10

80

200

D121

24

21.6 - 26.4

56

10

3.3

303.0

6.0

10

75

100

D122

24

21.6 - 26.4

54

10

5.0

200.0

4.0

10

77

100

D123

24

21.6 - 26.4

56

10

9.0

111.0

2.2

10

75

100

D124

24

21.6 - 26.4

53

10

12.0

83.3

1.6

10

78

100

D125

24

21.6 - 26.4

53

10

15.0

66.6

1.3

10

78

100

D126

24

21.6 - 26.4

56

10

±5.0

±100.0

±2.0

10

74

100

D127

24

21.6 - 26.4

54

10

±9.0

±55.5

±1.1

10

76

100

D128

24

21.6 - 26.4

53

10

±12.0

±41.6

±0.8

10

78

100

D129

24

21.6 - 26.4

53

10

±15.0

±33.3

±0.6

10

78

100

D131

48

43.2 - 52.8

29

6

3.3

303.0

6.0

10

72

100

D132

48

43.2 - 52.8

29

6

5.0

200.0

4.0

10

72

100

D133

48

43.2 - 52.8

28

6

9.0

111.0

2.2

10

74

100

D134

48

43.2 - 52.8

28

6

12.0

83.3

1.6

10

74

100

D135

48

43.2 - 52.8

28

6

15.0

66.6

1.3

10

75

100

D136

48

43.2 - 52.8

30

6

±5.0

±100.0

±2.0

10

70

100

D137

48

43.2 - 52.8

29

6

±9.0

±55.5

±1.1

10

72

100

D138

48

43.2 - 52.8

28

6

±12.0

±41.6

±0.8

10

74

100

D139

48

43.2 - 52.8

28

6

±15.0

±33.3

±0.6

10

74

100

Pin

Single

Dual

Pin

Single

Dual

1

+Vin

+Vin

5

No Pin

Common

2

-Vin

-Vin

6

+Vout

+Vout

4

-Vout

-Vout

Notes:

1. Output load regulation is specified for a load change of 20% to 100%.

2. These units do not require external components to operate, but the use of an input capacitor (10

μF) may enhance performance in some applications. It is recommended that an input capacitor

of 4.7 uF to 47 uF (dependent upon the application) be used on 48V input model.

An output capacitor (4.7 μF to 100 μF or ±4.7 μF to ±68 μF) may be used to reduce ripple. To

improve EMI performance, a simple filter network consisting of a 10 uF to 100 uF capacitor and

12 uH inductor should be effective.

3. These units will operate at no load without damage, but may not meet all specifications.

4. Dual output units may be connected to provide a 10V, 18V, 24V or 30 VDC output. To do this,

connect the load across the positive (+Vout) and negative (-Vout) outputs and float the output

common.

5. It is recommended that a fuse be used on the input of a power supply for

protection. See the table above for the correct rating.

Derating Curve

Notes:

the side of

MicroPower Direct

www.micropowerdirect.com

•

FAX: (781) 344-8481

•

E-Mail: sales@micropowerdirect.com

Model Selection Guide

Mechanical Dimensions

Pin Connections

Single Output

(μF Max)

220

Dual Output

(μF Max)

±100

Capacitive

Load

Other input/output combinations are available

(i.e. 24.0 VDC). Contact the factory for details at:

sales@micropowerdirect.com