Notes:

side of the unit

Model

Number

Input

Output

Load

Regulation

(%, Max)

Efficiency

(%, Typ)

Fuse Rating

Slow-Blow

(mA)

Voltage (VDC)

Current (mA)

Voltage

(VDC)

Current

(mA, Max)

Current

(mA, Min)

Nominal

Range

Full-Load

No-Load

DM101E

5

4.5 - 5.5

273

30

5.0

200.0

20.0

15

73

500

DM102E

5

4.5 - 5.5

270

30

12.0

83.0

9.0

15

74

500

DM103E

5

4.5 - 5.5

263

30

15.0

67.0

7.0

15

76

500

DM104E

5

4.5 - 5.5

278

30

±5.0

±100.0

±10.0

15

72

500

DM105E

5

4.5 - 5.5

256

30

±12.0

±42.0

±5.0

15

78

500

DM106E

5

4.5 - 5.5

256

30

±15.0

±33.0

±4.0

15

78

500

DM111E

12

10.8 - 13.2

107

15

5.0

200.0

20.0

15

78

200

DM112E

12

10.8 - 13.2

103

15

12.0

83.0

9.0

15

81

200

DM113E

12

10.8 - 13.2

105

15

15.0

67.0

7.0

15

79

200

DM114E

12

10.8 - 13.2

114

15

±5.0

±100.0

±10.0

15

73

200

DM115E

12

10.8 - 13.2

105

15

±12.0

±42.0

±5.0

15

79

200

DM116E

12

10.8 - 13.2

105

15

±15.0

±33.0

±4.0

15

79

200

Pin

Single

Dual

Pin

Single

Dual

1

+Vin

+Vin

5

No Pin

Common

2

-Vin

-Vin

6

+Vout

+Vout

4

-Vout

-Vout

Derating Curve

Notes:

1. Output load regulation is specified for a load change of

10% to 100%.

2. These units should not be operated with a load under 10%

of full load. Operation at no-load may cause damage to

the unit.

3. These converters will operate without external components.

However, when measuring output ripple, it is recommended

that an external ceramic capacitor be placed from the +Vout

pin to the -Vout pin for single output units and from each

output to common for dual output units. An input capaci-

tor will enhace stability over temperature and input line

variations. Recommended capacitor values are given in

the table above. For applications requiring very low output

noise levels, a simple LC filter should be effective.

4. Dual output units may be connected to provide a 10V, 24V

or 30 VDC output. To do this, connect the load across the

positive (+Vout) and negative (-Vout) outputs and float the

output common

5. It is recommended that a fuse be used on the input of a

power supply for protection. See the Model Selection table

above for the correct rating.

Vin

Input

Capacitor

Vout

Output Capacitor

Single

Dual

5 VDC

4.7

µF

5 VDC

10.0

µF

4.7

µF

12 VDC

2.2

µF

12 VDC

2.2

µF

1.0

µF

15 VDC

1.0

µF

0.47

µF

MicroPower Direct

www.micropowerdirect.com

292 Page Street Ste D Stoughton, MA 02072

•

TEL: (781) 344-8226

•

FAX: (781) 344-8481

•

E-Mail: sales@micropowerdirect.com

Model Selection Guide

Mechanical Dimensions

Pin Connections