Ultra Low-Power,

Single/Dual-Supply Comparators

2

_______________________________________________________________________________________

ABSOLUTE MAXIMUM RATINGS

V+ to V-, V+ to GND, GND to V-................................-0.3V, +12V

Inputs

Current, IN_+, IN_-, HYST...............................................20mA

Voltage, IN_+, IN_-, HYST................(V+ + 0.3V) to (V- – 0.3V)

Outputs

Current, REF....................................................................20mA

Current, OUT_ .................................................................50mA

Voltage, REF ....................................(V+ + 0.3V) to (V- – 0.3V)

Voltage, OUT_ (MAX921/924) .....(V+ + 0.3V) to (GND – 0.3V)

Voltage OUT_ (MAX922/923)...........(V+ + 0.3V) to (V- – 0.3V)

OUT_ Short-Circuit Duration (V+

≤ 5.5V) ...............Continuous

8-Pin Plastic DIP (derate 9.09mW/°C above +70°C) ...727mW

8-Pin SO (derate 5.88mW/°C above +70°C)................471mW

8-Pin µMAX (derate 4.1mW/°C above +70°C) .............330mW

8-Pin CERDIP (derate 8.00mW/°C above +70°C)........640mW

16-Pin Plastic DIP (derate 10.53mW/°C above +70°C)..842mW

16-Pin SO (derate 8.70mW/°C above +70°C) ................696mW

16-Pin CERDIP (derate 10.00mW/°C above +70°C) ......800mW

Operating Temperature Ranges:

MAX92_C_ _ .......................................................0°C to +70°C

MAX92_E_ _.....................................................-40°C to +85°C

MAX92_MJ_ ..................................................-55°C to +125°C

Storage Temperature Range .............................-65°C to +150°C

Lead Temperature (soldering, 10s) .................................+300°C

ELECTRICAL CHARACTERISTICS: 5V OPERATION

Stresses beyond those listed under “Absolute Maximum Ratings‘” may cause permanent damage to the device. These are stress ratings only, and functional

operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to

absolute maximum rating conditions for extended periods may affect device reliability.

PARAMETER

MAX923,

HYST = REF

MIN

TYP

MAX

UNITS

MAX924

7.5

V

V-

V+ – 1.3

5.5

6.5

MAX921,

HYST = REF

8.5

Supply Current

IN+ = IN- + 100mV

IN+ = IN- = 2.5V

11

µA

Supply Voltage Range

2.5

11

V

2.5

3.2

MAX922

4

5

2.5

3.2

Input Offset Voltage

CONDITIONS

M temp. range

±10

mV

C/E temp. ranges

M temp. range

±0.01

±5

nA

Input Leakage Current (IN-, IN+)

(Note 1)

±40

Input Leakage Current (HYST)

C/E temp. ranges

M temp. range

±0.02

nA

Input Common-Mode Voltage Range

C/E temp. ranges

Common-Mode Rejection Ratio

M temp. range

MAX921, MAX923

0.1

1.0

mV/V

Power-Supply Rejection Ratio

V- to (V+ – 1.3V)

V+ = 2.5V to 11V

100Hz to 100kHz

0.1

1.0

mV/V

Voltage Noise

MAX921, MAX923

Overdrive = 10mV

Overdrive = 100mV

20

Hysteresis Input Voltage Range

REF- 0.05V

REF

V

C/E temp. ranges

M temp. range

12

µs

Response Time

C/E temp. ranges

4

4

5

3.1

4.5

6

POWER REQUIREMENTS

COMPARATOR