| 数据搜索系统,热门电子元器件搜索 |
|
809-065C 数据表(PDF) 2 Page - Glenair, Inc. |
|
|
|||||||||||||||||||||||||||||
809-065C 数据表(HTML) 2 Page - Glenair, Inc. |
|
2 / 7 page ![]() A B C D E F G H J K L M Dimensions in inches (millimeters) and are subject to change without notice. © 2009 Glenair, Inc. CAGE Code 06324 Printed in U.S.A. GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912 www.glenair.com A-3 E-Mail: sales@glenair.com How To Terminate, Install and Remove Size #23 Contacts 2 StripWire.Removewireinsulation,takingcare to avoid nicking or cutting wire strands. Strip wire to length shown. 3 Insertwireintocontact.Thewireshouldbe visible in the inspection hole. 5 Inspectcrimpedcontact.Wireshouldbefully inserted and the crimp should be uniform in appearance. 1 SetUpCrimpTool.Installproperpositionerinto crimp tool. The label on the positioner shows the proper tool setting for each wire size. Turn the adjustment wheel to the correct setting. Crimp Tool Adjustment Wheel Positioner 6 Installcontactintoconnector.Pushthecontact through the rear grommet until the contact locks into place. This can usually be done by hand without the need for a tool. If the wire gage is #26 or smaller, a tool is helpful. There are two techniques for installing contacts with a tool. One method is to push the contact in by hand, then use the tool to finish the insertion. The other method is to position the insertion tip against the contact shoulder, then insert the contact. Use insertion/extraction tool 809-088 to install contacts. Slide the wire into the groove on the blue end of the tool. Slide the tool tip up the contact until it touches the contact shoulder. USE CARE TO AVOID DAMAGING THE CONNECTOR. 7 ContactExtraction.Usetool809-088.Thewhite end is used for contact extraction. First, push the wire into the groove of the metal tip. Slide the tip of the tool into the connector. Push the tool into the connector cavity until the tip bottoms in the connector. Avoid wiggling or rocking the tip.This may damage the cavity. A straight push is best. Pinch the wire between your finger and the white plastic grip and slide the tool and contact out of the connector. Wire insulation diameter greater than 0.045 inches (1.14mm) is too large to work properly with the extraction tool. connector damage is possible. .145/.155 (3.68/3.94) INSPECTION HOLE 1 2 3 4 Insertcontactintocrimptoolasshown.Make sure that the contact is fully inserted into the tool. Squeeze handle completely. The ratchet mechanism will not allow a partial crimp. Release handle and remove contact. 4 5 RUBBER GROMMET RETAINER TINE Insertion⁄Extraction Tool 809-088 RUBBER GROMMET 6 7 INSERTION TIP BLUE END EXTRACTION TIP WHITE END CONTACT RETAINER CLIP 4 Series 80 “Mighty Mouse” Contacts and Tools Size #23 Crimp Contact Instructions Rev. 03-FEB-2009 |
|
|
链接网址 |
| ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 数据表链接 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |