MAAPSS0076 datasheet(2/6 Pages) MA-COM

2 / 6 page

• North America Tel: 800.366.2266 / Fax: 978.366.2266

• Europe Tel: 44.1908.574.200 / Fax: 44.1908.574.300

• Asia/Pacific Tel: 81.44.844.8296 / Fax: 81.44.844.8298

Visit www.macomtech.com for additional data sheets and product information.

M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make

changes to the product(s) or information contained herein without notice.

DECT Power Amplifier

1880 - 1930 MHz

Rev. V3

MAAPSS0076

ADVANCED:

Data Sheets contain information regarding a product M/A-COM Technology Solutions

is considering for development. Performance is based on target specifications, simulated results,

and/or prototype measurements. Commitment to develop is not guaranteed.

PRELIMINARY:

Data Sheets contain information regarding a product M/A-COM Technology

Solutions has under development. Performance is based on engineering tests. Specifications are

typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available.

Commitment to produce in volume is not guaranteed.

Electrical Specifications: F = 1900 MHz, PIN = 0 dBm, VCC = 2.4 V, TA = 25 °C, Z0 = 50

Absolute Maximum Ratings

3,4

Parameter

Absolute Maximum

Input Power

+ 5 dBm

Operating Supply Voltage

+4.0 Volts

Operating Control Voltage

+3.0 Volts

Operating Temperature

-20 °C to +85 °C

Channel Temperature

+150 °C

Storage Temperature

-40 °C to +150 °C

Exceeding any one or combination of these limits may cause

permanent damage to this device.

M/A-COM does not recommend sustained operation near

these survivability limits.

Logic Table

VEN

State

OFF

LPM

HPM

5. 1 = +2.0 V to 2.5 V, 0 = 0 V to 0.5 V.

Operating the MAAPSS0076

The MAAPSS0076 is sensitive to electrostatic

discharge (ESD).

Use proper ESD control

techniques when handling this device. To operate

the MAAPSS0076, follow these steps. Ramp down

or shut down in reverse order.

1. Apply VCC (2.4 V).

2. Apply VM (0 or 2.5 V).

3. Apply PIN (-2 to 2 dBm).

4. Ramp VEN from 0 to 2.5 V.

Parameter

Test Conditions

Units

Min.

Typ.

Max.

Input Return Loss

VM = 0 V

VM = 2.5 V

—

POUT, High Power Mode (HPM)

VM = 2.5 V, VCC = 3.0 V

VCC = 2.4 V

VCC = 2.0 V

VCC = 1.8 V

dBm

—

26.5

25.5

24.0

23.5

—

POUT vs. Temperature, HPM

TA = 0 °C to 50 °C, VCC = 2.4 V

—

0.8

—

Current, HPM

VM = 2.5 V, VCC = 3.0 V

—

320

400

POUT, Low Power Mode (LPM)

VM = 0 V, VCC = 2.4 V

dBm

—

Current, LPM

VM = 0 V, VCC = 2.4 V

—

140

200

Current, Shutdown

VCC = 3.0 V, VEN = 0.5 V

µA

—

Control Pins

VEN, VM low

VEN, VM high

VM current

VEN current

2.0

—

0.5

2.5

1.0

3.0

Harmonics

VM = 2.5 V, VCC = 2.4 V

2fo

3fo

dBc

—

-50

-60

—

Forward Isolation

VEN = 0 V

Stability

+1.5 V < VCC < +3.5 V, POUT = HPM & LPM, VSWR < 6:1

-20

°C < TA < +70ºC, RBW = 3 MHz max. hold

Turn on/off time

ton: RF burst to (Avg Power – 1 dB)

toff: (Avg Power – 1 dB) to RF off

µS

—

All spurs < -60 dBc

POUT vs. VEN

VEN = 1.9 to 2.5 V

—

1.2

—

MAAPSS0076 数据表(PDF) 2 Page - M/A-COM Technology Solutions, Inc.

MAAPSS0076 数据表(HTML) 2 Page - M/A-COM Technology Solutions, Inc.

Html Pages

1 2 3 4 5 6

数据表下载