MCP4142T-104ESLASHML datasheet(49/88 Pages) MICROCHIP

49 / 88 page

DS22059B-page 49

MCP414X/416X/424X/426X

7.5

Write Data

Normal and High Voltage

The Write command is a 16-bit command. The Write

Command can be issued to both the Volatile and

Non-Volatile memory locations. The format of the

command is shown in Figure 7-2.

A Write command to a Volatile memory location

changes that location after a properly formatted Write

Command (16-clock) have been received.

A Write command to a Non-Volatile memory location

will only start a write cycle after a properly formatted

Write Command (16-clock) have been received and the

CS pin transitions to the inactive state (VIH).

7.5.1

SINGLE WRITE TO VOLATILE

MEMORY

The write operation requires that the CS pin be in the

active state (VILor VIHH). Typically, the CS pin will be in

the inactive state (VIH) and is driven to the active state

(VIL). The 16-bit Write Command (Command Byte and

Data Byte) is then clocked in on the SCK and SDI pins.

Once all 16 bits have been received, the specified

volatile address is updated. A write will not occur if the

write command isn’t exactly 16 clocks pulses. This

protects against system issues from corrupting the

Non-Volatile memory locations.

Figure 6-3 and Figure 6-4 show possible waveforms

for a single write.

7.5.2

SINGLE WRITE TO NON-VOLATILE

MEMORY

The sequence to write to to a single non-volatile

memory location is the same as a single write to volatile

memory with the exception that after the CS pin is

driven inactive (VIH), the EEPROM write cycle (tWC) is

started. A write cycle will not start if the write command

isn’t exactly 16 clocks pulses. This protects against

system issues from corrupting the Non-Volatile

memory locations.

After the CS pin is driven inactive (VIH), the serial

interface may immediately be re-enabled by driving the

CS pin to the active state (VILor VIHH).

During an EEPROM write cycle, only serial commands

to Volatile memory (addresses 00h, 01h, 04h, and 05h)

are accepted. All other serial commands are ignored

until the EEPROM write cycle (twc) completes. This

allows the Host Controller to operate on the Volatile

Wiper registers and the TCON register, and to Read

the Status Register. The EEWA bit in the Status register

indicates the status of an EEPROM Write Cycle.

Once a write command to a Non-Volatile memory

location has been received, NO other SPI commands

should be received before the CS pin transitions to the

inactive state (VIH) or the current SPI command will

have a Command Error (CMDERR) occur.

FIGURE 7-2:

Write Command - SDI and SDO States.

Note:

Writes to certain memory locations will be

dependant on the state of the WiperLock

Technology bits and the Write Protect bit.

1111111111111111 Valid Address/Command combination

111111

0 Invalid Address/Command combination (1)

COMMAND BYTE

DATA BYTE

SDI

SDO

Note 1:

If an Error Condition occurs (CMDERR = L), all following SDO bits will be low until the CMDERR

condition is cleared (the CS pin is forced to the inactive state).

MCP4142T-104E/ML 数据表(PDF) 49 Page - Microchip Technology

MCP4142T-104E/ML 数据表(HTML) 49 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88

数据表下载