MCP4142T-104ESLASHP datasheet(9/88 Pages) MICROCHIP

9 / 88 page

DS22059B-page 9

MCP414X/416X/424X/426X

Digital Inputs/Outputs (CS, SDI, SDO, SCK, WP, SHDN)

Schmitt Trigger

High Input

Threshold

VIH

0.45 VDD

——

2.7V

≤ VDD ≤ 5.5V

(Allows 2.7V Digital VDD with

5V Analog VDD)

0.5 VDD

——

1.8V

≤ VDD ≤ 2.7V

Schmitt Trigger

Low Input

Threshold

VIL

—

0.2VDD

Hysteresis of

Schmitt Trigger

Inputs

VHYS

—0.1VDD

—V

High Voltage Input

Entry Voltage

VIHH

8.5

—

12.5 (6)

Threshold for WiperLock™ Technology

High Voltage Input

Exit Voltage

VIHH

——

VDD +

0.8V (6)

High Voltage Limit

VMAX

——

12.5 (6)

Pin can tolerate VMAX or less.

Output Low

Voltage (SDO)

VOL

VSS

—0.3VDD

VIOL = 5 mA, VDD = 5.5V

VSS

—0.3VDD

VIOL = 1 mA, VDD = 1.8V

Output High

Voltage (SDO)

VOH

0.7VDD

—VDD

VIOH = -2.5 mA, VDD = 5.5V

0.7VDD

—VDD

VIOL = -1 mA, VDD = 1.8V

Weak Pull-up /

Pull-down Current

IPU

—

1.75

Internal VDD pull-up, VIHH pull-down,

VDD = 5.5V, VCS = 12.5V

—170

—

µA

CS pin, VDD = 5.5V, VCS = 3V

CS Pull-up /

Pull-down

Resistance

RCS

—16

—

kΩ

VDD = 5.5V, VCS = 3V

Input Leakage

Current

IIL

-1

—

µA

VIN = VDD and VIN = VSS

Pin Capacitance

CIN, COUT

—10

—

fC = 20 MHz

AC/DC CHARACTERISTICS (CONTINUED)

DC Characteristics

Standard Operating Conditions (unless otherwise specified)

Operating Temperature

–40°C

≤ TA ≤ +125°C (extended)

All parameters apply across the specified operating ranges unless noted.

VDD = +2.7V to 5.5V, 5 kΩ, 10 kΩ, 50 kΩ, 100 kΩ devices.

Typical specifications represent values for VDD = 5.5V, TA = +25°C.

Parameters

Sym

Min

Typ

Max

Units

Conditions

Note 1:

Resistance is defined as the resistance between terminal A to terminal B.

INL and DNL are measured at VW with VA = VDD and VB = VSS.

MCP4XX1

only.

MCP4XX2

only, includes VWZSE and VWFSE.

Resistor terminals A, W and B’s polarity with respect to each other is not restricted.

This specification by design.

Non-linearity is affected by wiper resistance (RW), which changes significantly over voltage and

temperature.

The MCP4XX1 is externally connected to match the configurations of the MCP41X2 and MCP42X2, and

then tested.

POR/BOR is not rate dependent.

10:

Supply current is independent of current through the resistor network

MCP4142T-104E/P 数据表(PDF) 9 Page - Microchip Technology

MCP4142T-104E/P 数据表(HTML) 9 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88

数据表下载

链接网址

MCP4142T-104E/P 数据表(PDF) 9 Page - Microchip Technology

MCP4142T-104E/P 数据表(HTML) 9 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88

数据表 下载

链接网址

数据表下载