MCP4641-103ESLASHML datasheet(65/92 Pages) MICROCHIP

65 / 92 page

DS22107A-page 65

MCP454X/456X/464X/466X

7.8

Modify Write Protect or WiperLock

Technology (High Voltage)

Enable and Disable

These commands are special cases of the High Volt-

age Decrement Wiper and the High Voltage Incre-

ment Wiper commands to the non-volatile memory

locations 02h, 03h, and 0Fh. This command is used to

enable or disable either the software Write Protect,

wiper 0 WiperLock Technology, or wiper 1 WiperLock

Technology. Table 7-6 shows the memory addresses,

the High Voltage command and the result of those

commands on the non-volatile WP, WL0, 0r WL1 bits.

7.8.1

SINGLE MODIFY (ENABLE OR

DISABLE) WRITE PROTECT OR

WIPERLOCK TECHNOLOGY (HIGH

VOLTAGE)

Figure 7-9 (Disable) and Figure 7-10 (Enable) show

the formats for a single Modify Write Protect or Wiper-

Lock Technology command.

A Modify Write Protect or WiperLock Technology

Command will only start an EEPROM write cycle (twc)

after a properly formatted Command has been

received and the Stop condition occurs.

During an EEPROM write cycle, only serial commands

to Volatile memory (addresses 00h, 01h, 04h, and 05h)

are accepted. All other serial commands are ignored

until the EEPROM write cycle (twc) completes. This

allows the Host Controller to operate on the Volatile

Wiper registers and the TCON register, and to Read

the Status Register. The EEWA bit in the Status register

indicates the status of an EEPROM Write Cycle.

TABLE 7-6:

ADDRESS MAP TO MODIFY WRITE PROTECT AND WIPERLOCK TECHNOLOGY

FIGURE 7-9:

I2C Disable Command Sequence.

FIGURE 7-10:

I2C Enable Command Sequence.

Memory

Address

Command’s and Result

High Voltage Decrement Wiper

High Voltage Increment Wiper

00h

Wiper 0 register is incremented

01h

Wiper 1 register is decremented

Wiper 1 register is incremented

02h

WL0 is enabled

WL0 is disabled

03h

WL1 is enabled

WL1 is disabled

04h (1)

TCON register not changed

05h - 0Eh (1)

Reserved

0Fh

WP is enabled

WP is disabled

Note 1:

Reserved addresses: Increment or Decrement commands are invalid for these addresses.

Control Byte

Disable Command

SA2 A1 A0 0

AD AD AD AD

A1 X

X A

Fixed

Address

Variable

Address

Device

Memory

Address

Command (Increment)

Write bit

Control Byte

Enable Command

SA2 A1 A0 0

AD AD AD AD

A0 X

X A P

Fixed

Address

Variable

Address

Device

Memory

Address

Command (Decrement)

Write bit

MCP4641-103E/ML 数据表(PDF) 65 Page - Microchip Technology

MCP4641-103E/ML 数据表(HTML) 65 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92

数据表下载

链接网址

MCP4641-103E/ML 数据表(PDF) 65 Page - Microchip Technology

MCP4641-103E/ML 数据表(HTML) 65 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92

数据表 下载

链接网址

数据表下载