500 MHz to 1700 MHz Balanced Mixer,

LO Buffer and RF Balun

ADL5367

Rev. 0

Information furnished by Analog Devices is believed to be accurate and reliable. However, no

responsibilityis assumedbyAnalogDevicesforitsuse,norforanyinfringementsof patentsorother

rightsofthirdpartiesthatmayresultfromitsuse.Specificationssubjecttochangewithoutnotice.No

license is granted by implication or otherwise under any patent or patent rights of Analog Devices.

Trademarksandregisteredtrademarksarethepropertyoftheirrespectiveowners.

One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.

Tel: 781.329.4700

www.analog.com

Fax: 781.461.3113

©2009 Analog Devices, Inc. All rights reserved.

FEATURES

RF frequency range of 500 MHz to 1700 MHz

IF frequency range of 30 MHz to 450 MHz

Power conversion loss: 7.7 dB

SSB noise figure of 8.3 dB

SSB noise figure with 5 dBm blocker of 21 dB

Input IP3 of 34 dBm

Typical LO drive of 0 dBm

Single-ended, 50 Ω RF and LO input ports

High isolation SPDT LO input switch

Single-supply operation: 3.3 V to 5 V

Exposed paddle 5 mm × 5 mm, 20-lead LFCSP

1500 V HBM/500 V FICDM ESD performance

APPLICATIONS

Cellular base station receivers

Transmit observation receivers

Radio link downconverters

GENERAL DESCRIPTION

The ADL5367 uses a highly linear, doubly balanced passive

mixer core along with integrated RF and LO balancing circuitry

to allow for single-ended operation. The ADL5367 incorporates

an RF balun, allowing optimal performance over a 500 MHz to

1700 MHz RF input frequency range. Performance is optimized for

RF frequencies from 500 MHz to 1200 MHz using a high-side LO

and for RF frequencies from 900 MHz to 1700 MHz using a

low-side LO. The balanced passive mixer arrangement provides

good LO-to-RF leakage, typically better than −35 dBm, and

excellent intermodulation performance. The balanced mixer

core also provides extremely high input linearity, allowing the

device to be used in demanding cellular applications where in-

band blocking signals may otherwise result in the degradation

of dynamic performance. A high linearity IF buffer amplifier

follows the passive mixer core to yield a typical power conversion

loss of 7.7 dB and can be used with a wide range of output

impedances.

FUNCTIONAL BLOCK DIAGRAM

2

3

1

20

19

18

17

16

6

7

8

9

10

4

5

14

13

15

12

BIAS

GENERATOR

VPMX

RFIN

RFCT

COMM

COMM

LOI2

VPSW

VGS1

VGS0

LOI1

VCMI

IFOP

IFON

PWDN

COMM

VLO3

LGM3

VLO2

LOSW

NC

ADL5367

NC = NO CONNECT

11

Figure 1.

The ADL5367 provides two switched LO paths that can be

used in TDD applications where it is desirable to rapidly switch

between two local oscillators. LO current can be externally set

using a resistor to minimize dc current commensurate with the

desired level of performance. For low voltage applications, the

ADL5367 is capable of operation at voltages down to 3.3 V with

substantially reduced current. Under low voltage operation, an

additional logic pin is provided to power down (<200 μA) the

circuit when desired.

The ADL5367 is fabricated using a BiCMOS high performance

IC process. The device is available in a 5 mm × 5 mm, 20-lead

LFCSP and operates over a −40°C to +85°C temperature range.

An evaluation board is also available.

Table 1. Passive Mixers

RF Frequency

(MHz)

Single

Mixer

Single Mixer +

IF Amp

Dual Mixer +

IF Amp

500 to 1700

ADL5367

ADL5357

ADL5358

1200 to 2500

ADL5365

ADL5355

ADL5356