ATmega16 datasheet(290/357 Pages) ATMEL

290 / 357 page

290

2466S–AVR–05/09

ATmega16(L)

Programming the

Fuses

Enter JTAG instruction PROG_COMMANDS.

Enable Fuse write using programming instruction 6a.

Load data High byte using programming instructions 6b. A bit value of “0” will program

the corresponding fuse, a “1” will unprogram the fuse.

Write Fuse High byte using programming instruction 6c.

Poll for Fuse write complete using programming instruction 6d, or wait for t

WLRH (refer to

Table 113 on page 272).

Load data Low byte using programming instructions 6e. A “0” will program the fuse, a “1”

will unprogram the fuse.

Write Fuse Low byte using programming instruction 6f.

Poll for Fuse write complete using programming instruction 6g, or wait for t

WLRH (refer to

Table 113 on page 272).

Programming the Lock

Bits

Enter JTAG instruction PROG_COMMANDS.

Enable Lock bit write using programming instruction 7a.

Load data using programming instructions 7b. A bit value of “0” will program the corre-

sponding Lock bit, a “1” will leave the Lock bit unchanged.

Write Lock bits using programming instruction 7c.

Poll for Lock bit write complete using programming instruction 7d, or wait for t

WLRH (refer

to Table 113 on page 272).

Reading the Fuses

and Lock Bits

Enter JTAG instruction PROG_COMMANDS.

Enable Fuse/Lock bit read using programming instruction 8a.

To read all Fuses and Lock bits, use programming instruction 8e.

To only read Fuse High byte, use programming instruction 8b.

To only read Fuse Low byte, use programming instruction 8c.

To only read Lock bits, use programming instruction 8d.

Reading the Signature

Bytes

Enter JTAG instruction PROG_COMMANDS.

Enable Signature byte read using programming instruction 9a.

Load address $00 using programming instruction 9b.

Read first signature byte using programming instruction 9c.

Repeat steps 3 and 4 with address $01 and address $02 to read the second and third

signature bytes, respectively.

Reading the

Calibration Byte

Enter JTAG instruction PROG_COMMANDS.

Enable Calibration byte read using programming instruction 10a.

Load address $00 using programming instruction 10b.

Read the calibration byte using programming instruction 10c.

ATmega16 数据表(PDF) 290 Page - ATMEL Corporation

ATmega16 数据表(HTML) 290 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载

链接网址

ATmega16 数据表(PDF) 290 Page - ATMEL Corporation

ATmega16 数据表(HTML) 290 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表 下载

链接网址

数据表下载