bq20z65-R1

SLUS990 – DECEMBER 2009

www.ti.com

TERMINAL FUNCTIONS

TERMINAL

DESCRIPTION

NO.

NAME

1

DSG

O

High side N-chan discharge FET gate drive

Battery pack input voltage sense input. It also serves as device wake up when device is in shutdown

2

PACK

IA, P

mode.

Positive device supply input. Connect to the center connection of the CHG FET and DSG FET to

3

VCC

P

ensure device supply either from battery stack or battery pack input

4

ZVCHG

O

P-chan pre-charge FET gate drive

High voltage general purpose open drain output. Can be configured to be used in pre-charge

5

GPOD

OD

condition

Pre-charge mode setting input. Connect to PACK to enable 0v pre-charge using charge FET

6

PMS

I

connected at CHG pin. Connect to VSS to disable 0V pre-charge using charge FET connected at

CHG pin.

7

VSS

P

Negative supply voltage input. Connect all VSS pins together for operation of device

8

REG33

P

3.3V regulator output. Connect at least a 2.2

μF capacitor to REG33 and VSS

9

TOUT

P

Thermistor bias supply output

10

VCELL+

-

Internal cell voltage multiplexer and amplifier output. Connect a 0.1

μF capacitor to VCELL+ and VSS

Alert output. In case of short circuit condition, overload condition and watchdog time out this pin will

11

ALERT

OD

be triggered.

12

NC

-

Not used - leave floating

13

TS1

IA

14

TS2

IA

15

PRES

I

Active low input to sense system insertion. Typically requires additional ESD protection.

Active low input to detect secondary protector status, and to allow the bq20z65-R1 to report the

16

PFIN

I

17

SAFE

OD

Active high output to enforce additional level of safety protection; e.g., fuse blow.

SMBus data open-drain bidirectional pin used to transfer address and data to and from the

18

SMBD

I/OD

bq20z65-R1

19

NC

-

Not used - leave floating

SMBus clock open-drain bidirectional pin used to clock the data transfer to and from the

20

SMBC

I/OD

bq20z65-R1

Display control for the LEDs. This pin is typically connected to VCC via a 100k

Ω resistor and a push

21

DISP

I

button switch connected to VSS.

22

VSS

P

Negative supply voltage input. Connect all VSS pins together for operation of device

23

LED1

I

LED1 display segment that drives an external LED depending on the firmware configuration

24

LED2

I

LED2 display segment that drives an external LED depending on the firmware configuration

25

LED3

I

LED3 display segment that drives an external LED depending on the firmware configuration

26

LED4

I

LED4 display segment that drives an external LED depending on the firmware configuration

27

LED5

I

LED5 display segment that drives an external LED depending on the firmware configuration

28

GSRP

IA

Coulomb counter differential input. Connect to one side of the sense resistor

29

GSRN

IA

Coulomb counter differential input. Connect to one side of the sense resistor

Master reset input that forces the device into reset when held low. Must be held high for normal

30

MRST

I

operation. Connect to RESET for correct operation of device

31

VSS

P

Negative supply voltage input. Connect all VSS pins together for operation of device

32

REG25

P

2.5V regulator output. Connect at least a 1mF capacitor to REG25 and VSS

RAM / Register backup input. Connect a capacitor to this pin and VSS to protect loss of RAM /

33

RBI

P

Register data in case of short circuit condition.

34

VSS

P

Negative supply voltage input. Connect all VSS pins together for operation of device

35

RESET

O

Reset output. Connect to MSRT.

36

ASRN

IA

Short circuit and overload detection differential input. Connect to sense resistor

37

ASRP

IA

Short circuit and overload detection differential input. Connect to sense resistor

(1)

I = Input, IA = Analog input, I/O = Input/output, I/OD = Input/Open-drain output, O = Output, OA = Analog output, P = Power

4

Submit Documentation Feedback

Copyright © 2009, Texas Instruments Incorporated

Product Folder Link(s): bq20z65-R1