Snap Action Switch

D2F

35

■ Dimensions and Operating Characteristics

Note: 1. Unless otherwise specified, all units are in millimeters and a tolerance of

±0.4 mm applies to all dimensions

2. Omitted dimensions are the same as pin plunger type.

3. The following illustrations and dimensions are for models with PCB terminals. Refer to “Terminals” for models with self-supporting, solder

and right / left angle terminal specifics.

4. The operating characteristics are for operation in the A direction(

)

Pin Plunger Models

D2F-

D2F-01-

D2F-F-

D2F-01F-

2.2

+0.12

0

dia.

2

+0.12

0

dia. holes

12.7

1.2

5.2

5OP

1.5

3.5

0.9

0.4

5.8

±0.15

12.8

±0.15

5.08

5.08

6.5

±0.1

3.15

5.7

2.9

2

+0.12

0

PT

A

Characteristics

D2F-

@

D2F-01-

@

D2F-F-

@

D2F-01F-

@

OF max.

150 g

75 g

RF min.

20 g

5 g

PT max.

0.5 mm

0.5 mm

OT min.

0.25 mm

0.25 mm

MD max.

0.12 mm

0.12 mm

OP

5.5

± 0.3 mm

5.5

± 0.3 mm

FP max.

——

Hinge Lever Models

D2F-L-

D2F-01L-

D2F-FL-

D2F-01FL-

t = 0.3 (see note)

12.8

(10.8)

OP

FP

3

Note:

Stainless-steel lever

A

Characteristics

D2F-L-

@

D2F-01L-

@

D2F-FL-

@

D2F-01FL-

@

OF max.

80 g

25 g

RF min.

5 g

2 g

PT max.

——

OT min.

0.55 mm

0.55 mm

MD max.

0.5 mm

0.5 mm

OP

6.8

± 1.5 mm

6.8

± 1.5 mm

FP max.

10 mm

10 mm

Simulated Roller Lever Models

D2F-L3-

D2F-01L3-

D2F-FL3-

D2F-01FL3-

t = 0.3 (see note)

1.3R

12.7

(7.5)

10

2.1

OP

FP

3

Note:

Stainless-steel lever

A

Characteristics

D2F-L3-

@

D2F-01L3-

@

D2F-FL3-

@

D2F-01FL3-

@

OF max.

80 g

40 g

RF min.

5 g

2 g

PT max.

——

OT min.

0.5 mm

0.5 mm

MD max.

0.45 mm

0.45 mm

OP

8.5

± 1.2 mm

8.5

± 1.2 mm

FP max.

13 mm

13 mm

Hinge Roller Lever Models

D2F-L2-

D2F-01L2-

D2F-FL2-

D2F-01FL2-

Note:

Stainless-steel lever

4.8 dia.

× 2.8 (Resin roller)

t = 0.3

(see

note)

(4.6)

OP FP

4

12.8

(10)

4

A

Characteristics

D2F-L2-

@

D2F-01L2-

@

D2F-FL2-

@

D2F-01FL2-

@

OF max.

80 g

40 g

RF min.

5 g

2 g

PT max.

——

OT min.

0.55 mm

0.55 mm

MD max.

0.5 mm

0.5 mm

OP

13

± 2.0 mm

13

± 2.0 mm

FP max.

16.5 mm

16.5 mm