| 数据搜索系统,热门电子元器件搜索 |
|
XWM8148CFT/V 数据表(PDF) 16 Page - Wolfson Microelectronics plc |
|
|
|||||||||||||||||||||||||||||
XWM8148CFT/V 数据表(HTML) 16 Page - Wolfson Microelectronics plc |
|
16 / 43 page ![]() WM8148 Production Data WOLFSON MICROELECTRONICS LTD PD Rev 4.0 April 1999 16 INPUT SAMPLING MODES To suit different sensors and applications, the WM8148 can sample one, two, or three channels simultaneously, at the rate of the VSMP clock. In each case there are two possible ratios of VSMP frequency to the MCLK master clock frequency, and a choice of whether to use CDS. Table 1 summarises the options available, including the respective maximum sample rates. The mode of operation is set by the Control Register bits MODE[3:0] as shown. Note MODE[0] defines whether or not CDS is activated. MAX SAMPLE RATE PER CHANNEL (VSMP) MCLK/VSMP FREQUENCY RATIO MAX MCLK FREQENCY MAX OUTPUT RATE MODE NUMBER (MODE[3:0]) MSPS MHz MSPS CDS NON- CDS Three-channel (8-phase) 4 8 32 12 0 1 Three-channel (12-phase) 412 48 12 8 9 Two-channel (6-phase) 5.33 6 32 10.66 4 5 Two-channel (8-phase) 6 8 48 12 12 13 One-channel CDS 6.66 6 40 6.66 2 N/A One-channel non-CDS 10 4 40 10 N/A 3 Table 1 Modes of Operation If an external VSMP signal is not available, the WM8148 can be configured to output a synchronisation pulse to the system by setting control bit FREE. The internally generated signal is presented on the VSMP and/or SDO pins depending on the settings of the control bits VSMPOP and SDO[1:0]. CORRELATED DOUBLE SAMPLING (CDS) The input signal can be sampled in two ways: Correlated Double Sampling (CDS), or non-CDS. CDS operation is summarised in Figure 15. The video signal processed is the difference between the voltage applied at the RINP input when RS turns off and the voltage at the RINP input when VS turns off, i.e. the difference between reset and video levels from the same pixel of the input signal. This method of sampling is recommended as it removes common-mode noise. R S V S V RS V VS Figure 15 CDS Reset and Video Level Sampling In non-CDS modes, RS and VS occur simultaneously. VS samples the video signal, while RS samples the reference level applied to the VRLC pin. The video signal processed is the difference between these samples (VRS-VVS). The voltage (VVRLC), on pin VRLC, may be driven externally or internally by the RLC DAC. In these modes d.c. variations of the input signal are not rejected. |
|
链接网址 |
| ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 数据表链接 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |