ALUMINUM ELECTROLYTIC CAPACITORS

C H I P T Y P E S E R I E S

TS13C0

F E A T U R E S

‧

Designed for surface mounting on high density circuit board.

‧

Emboss carrier tape packing system is available for automatic insertion.

Standard Series

Specifications

I

T

E

M

S P E R F O R M A N C E C H A R A C T E R I S T I C S

Operating Temperature Range

-40℃ ~ +85℃

Voltage Range

4~100V

Capacitance Range

0.1~10000μF

Capacitance Tolerance

±20% at 120Hz, 20℃

Leakage Current

Leakage current(φ4~φ10)≤0.01CV or 3μA,, whichever is greater.( After 2 minutes’ application of rated voltage)

Leakage current(φ12.5~φ16)≤0.03CV or 4μA,, whichever is greater.( After 1 minutes’ application of rated voltage)

Tan δ

Measurement frequency : 120Hz, Temperature : 20℃

Rated voltage (V)

4

6.3

10

16

25

35

50

63

100

φ

4~φ10

0.35

0.26

0.20

0.16

0.14

0.12

0.12

0.10

0.10

Tan δ (MAX)

φ

12.5~φ16

0.42

0.38

0.34

0.30

0.26

0.22

0.18

0.14

0.10

Stability at Low Temperature

Measurement frequency : 120Hz

Rated voltage (V)

4

6.3

10

16

25

35

50~100

Z-25℃ / Z+20℃

7

4

3

2

2

2

2

φ

4~φ10

Z-40℃ / Z+20℃

15

8

6

4

4

3

3

Z-25℃ / Z+20℃

7

5

4

3

2

2

2

Impedance ratio

ZT / Z20 (MAX)

φ

12.5~φ16

Z-40℃ / Z+20℃

17

12

10

8

5

4

3

Load Life

After 2000 hours’ application of

rated voltage at 85℃, capacitors

meet the characteristics

requirements listed at right

Capacitance Change

Within ± 20% of initial value

(Within ± 25% of initial value for 4V)

Tan δ

200% or less of initial specified value

Leakage Current

Initial specified value or less

Self Life

After leaving capacitors under no load at 85℃ for 1000 hours, they meet the specified value for load life characteristics listed above.

Resistance to Soldering Heat

The capacitors shall be kept on the hot plate

maintained at 250℃ for 30 seconds. After

removing from the hot plate and restored at

room temperature, they meet the characteristics

requirements listed at right.

Capacitance Change

Within ± 10% of initial value

Tan δ

Initial specified value or less

Leakage Current

Initial specified value or less

Applicable Standards

JIS C-5141 and JIS C-5102.

Chip type

1 Voltage mark [6V] represents 6.3V for Ф4～Ф10;

*2 [L±0.3] is applicable to Φ6.3×7.7 and Φ8×6.2;

*3 [L±0.5] is applicable to Φ8×10.5～Ф10;

*4 [L±1.0] is applicable to Φ12.5～Ф16.

(mm)

Ø

DxL

4x5.4

5x5.4

6.3x5.4

8x6.2

6.3x7.7

8x10.5

10x10.5/13.5

12.5x13.5

12.5x16

16x16.5/21.5

A

1.8

2.1

2.4

3.3

2.4

2.9

3.2

4.7

4.7

5.5

B

4.3

5.3

6.6

8.3

6.6

8.3

10.3

13.0

13.0

17.0

C

4.3

5.3

6.6

8.3

6.6

8.3

10.3

13.0

13.0

17.0

E±0.2

1.0

1.3

2.2

2.2

2.2

3.1

4.4

4.4

4.4

6.7

L

5.4

5.4

5.4

6.2

7.7

10.5

10.5/13.5

13.5

16.0

16.5/21.5

Suntan

Website: www.suntan.com.hk

Email: info@suntan.com.hk

Tel: (852) 8202 8782

Fax: (852) 8208 6246