| 数据搜索系统,热门电子元器件搜索 |
|
CS5525-ASZ 数据表(PDF) 12 Page - Cirrus Logic |
|
|
|||||||||||||||||||||||||||||
CS5525-ASZ 数据表(HTML) 12 Page - Cirrus Logic |
|
12 / 30 page ![]() CS5525 CS5526 12 DS202F5 Configuration Register * R indicates the bit value after the part is reset D23(MSB) D22 D21 D20 D19 D18 D17 D16 D15 D14 D13 D12 A3 A2 A1 A0 NU CFS NU LPM WR2 WR1 WR0 U/B D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 G2 G1 G0 PD RS RV PF PSS DF CC2 CC1 CC0 BIT NAME VALUE FUNCTION D23-D20 Latch Outputs, A3-A0 0000 R* Latch Output Pins A3-A0 mimic the D23-D20 Register bits. D19 Not Used, NU 0 R Must always be logic 0. D18 Chop Frequency Select, CFS 0 1 R 256 Hz Amplifier chop frequency 32768 Hz Amplifier chop frequency D17 Not Used, NU 0 R Must always be logic 0. D16 Low Power Mode, LPM 0 1 R Normal Mode Reduced Power mode D15-D13 Word Rate, WR2-0 Note: For XIN = 32.768kHz 000 001 010 011 100 101 110 111 R 15.0 Sps (2182 XIN cycles) 30.1 Sps (1090 XIN cycles) 60.0 Sps (546 XIN cycles) 123.2 Sps (266 XIN cycles) 168.9 Sps (194 XIN cycles) 202.3 Sps (162 XIN cycles) 3.76 Sps (8722 XIN cycles) 7.51 Sps (4362 XIN cycles) D12 Unipolar/Bipolar, U/B 0 1 R Bipolar Measurement mode Unipolar Measurement mode D11-D9 Gain Bits, G2-G0 000 001 010 011 100 101 110/111 R 100 mV (assumes VREF = 2.5V) 55 mV 25 mV 1V 5.0 V 2.5 V Not Used. D8 Pump Disable, PD 0 1 R Charge Pump Enabled For PD = 1, the CPD pin goes to a Hi-Z output state. D7 Reset System, RS 0 1 R Normal Operation Activate a Reset cycle. To return to Normal Operation write bit to zero. D6 Reset Valid , RV 0 1R No reset has occurred or bit has been cleared (read only). Valid Reset has occurred. (Cleared when read.) D5 Port Flag, PF 0 1 R Port Flag mode inactive Port Flag mode active D4 Power Save Select, PSS 0 1 R Standby Mode (Oscillator active, allows quick power-up) Sleep Mode (Oscillator inactive) D3 Done Flag, DF 0 1 R Done Flag bit is cleared (read only). Calibration or Conversion cycle completed (read only). D2-D0 Calibration Control Bits, CC2-CC0 000 001 010 011 100 101 110 111 R Normal Operation (no calibration) Offset -- Self-Calibration Gain -- Self-Calibration Offset Self-Calibration followed by Gain Self-Calibration Not used. Offset -- System Calibration Gain -- System Calibration Not Used. Table 2. Configuration Register |
|
|
链接网址 |
| ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 数据表链接 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |