PIC16F505-ESLASHST datasheet(71/110 Pages) MICROCHIP

71 / 110 page

DS41236E-page 71

PIC12F508/509/16F505

10.1

DC Characteristics: PIC12F508/509/16F505 (Industrial)

DC Characteristics

Standard Operating Conditions (unless otherwise specified)

Operating Temperature -40

°C ≤ TA ≤ +85°C (industrial)

Param

No.

Sym.

Characteristic

Min.

Typ(1)

Max.

Units

Conditions

D001

VDD

Supply Voltage

2.0

5.5

See Figure 10-1

D002

VDR

RAM Data Retention Voltage(2)

—

1.5*

—

Device in Sleep mode

D003

VPOR VDD Start Voltage to ensure

Power-on Reset

—

Vss

—

See Section 7.4 "Power-on

Reset (POR)" for details

D004

SVDD VDD Rise Rate to ensure

Power-on Reset

0.05*

—

V/ms

See Section 7.4 "Power-on

Reset (POR)" for details

D010

IDD

Supply Current(3,4)

—

175

0.625

275

1.1

μA

FOSC = 4 MHz, VDD = 2.0V

FOSC = 4 MHz, VDD = 5.0V

—

500

1.5

650

2.2

μA

FOSC = 10 MHz, VDD = 3.0V

FOSC = 20 MHz, VDD = 5.0V

(PIC16F505 only)

—

μA

FOSC = 32 kHz, VDD = 2.0V

FOSC = 32 kHz, VDD = 5.0V

D020

IPD

Power-down Current(5)

—

0.1

0.35

1.2

2.4

μA

VDD = 2.0V

VDD = 5.0V

D022

IWDT

WDT Current(5)

—

1.0

7.0

3.0

16.0

μA

VDD = 2.0V

VDD = 5.0V

These parameters are characterized but not tested.

Note 1:

Data in the Typical (“Typ”) column is based on characterization results at 25

°C. This data is for design

guidance only and is not tested.

This is the limit to which VDD can be lowered in Sleep mode without losing RAM data.

The supply current is mainly a function of the operating voltage and frequency. Other factors such as bus

loading, oscillator type, bus rate, internal code execution pattern and temperature also have an impact on

the current consumption.

The test conditions for all IDD measurements in active operation mode are:

OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VSS, T0CKI = VDD, MCLR =

VDD; WDT enabled/disabled as specified.

For standby current measurements, the conditions are the same as IDD, except that the device is in Sleep

mode. If a module current is listed, the current is for that specific module enabled and the device in Sleep.

PIC16F505-E/ST 数据表(PDF) 71 Page - Microchip Technology

PIC16F505-E/ST 数据表(HTML) 71 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载