数据搜索系统,热门电子元器件搜索
  Chinese  ▼
ALLDATASHEETCN.COM

X  

LT1766IGN 数据表(PDF) 24 Page - Linear Technology

部件名 LT1766IGN
功能描述  5.5V to 60V 1.5A, 200kHz Step-Down Switching Regulator
PDF  30 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
制造商  LINER [Linear Technology]
网页  http://www.linear.com
标志 LINER - Linear Technology

LT1766IGN 数据表(HTML) 24 Page - Linear Technology

Back Button LT1766IGN Datasheet HTML 20Page - Linear Technology LT1766IGN Datasheet HTML 21Page - Linear Technology LT1766IGN Datasheet HTML 22Page - Linear Technology LT1766IGN Datasheet HTML 23Page - Linear Technology LT1766IGN Datasheet HTML 24Page - Linear Technology LT1766IGN Datasheet HTML 25Page - Linear Technology LT1766IGN Datasheet HTML 26Page - Linear Technology LT1766IGN Datasheet HTML 27Page - Linear Technology LT1766IGN Datasheet HTML 28Page - Linear Technology Next Button
Zoom Inzoom in Zoom Outzoom out
 24 / 30 page
background image
LT1766/LT1766-5
24
1766fc
When using RC, the maximum value has two limitations.
First, the combination of output capacitor ESR and RC
may stop the loop rolling off altogether. Second, if the
loop gain is not rolled off sufficiently at the switching
frequency, output ripple will peturb the VC pin enough to
cause unstable duty cycle switching similar to subharmonic
oscillations. If needed, an additional capacitor, CF, can be
added across the RC/CC network from the VC pin to ground
to further suppress VC ripple voltage.
With a tantalum output capacitor, the LT1766 already in-
cludes a resistor, RC and filter capacitor, CF, at the VC pin
(see Figures 10 and 11) to compensate the loop over the
entire VIN range (to allow for stable pulse skipping for high
VIN-to-VOUT ratios ≥10). A ceramic output capacitor can
still be used with a simple adjustment to the resistor RC
for stable operation. (See Ceramic Capacitors section for
stabilizing LT1766). If additional phase margin is required,
a capacitor, CFB, can be inserted between the output and FB
pin but care must be taken for high output voltage applica-
tions. Sudden shorts to the output can create unacceptably
large negative transients on the FB pin.
For VIN-to-VOUT ratios <10, higher loop bandwidths are
possible by readjusting the frequency compensation
components at the VC pin.
When checking loop stability, the circuit should be op-
erated over the applications’s full voltage, current and
temperature range. Proper loop compensation may be
obtained by emperical methods as described in detail in
Application Notes 19 and 76.
CONVERTER WITH BACKUP OUTPUT REGULATOR
In systems with a primary and backup supply, for example,
a battery-powered device with a wall adapter input, the
output of the LT1766 can be held up by the backup supply
with the LT1766 input disconnected. In this condition, the
SW pin will source current into the VIN pin. If the SHDN pin
is held at ground, only the shut down current of 25μA will
be pulled via the SW pin from the second supply. With the
SHDN pin floating, the LT1766 will consume its quiescent
operating current of 1.5mA. The VIN pin will also source
current to any other components connected to the input
line. If this load is greater than 10mA or the input could
be shorted to ground, a series Schottky diode must be
added, as shown in Figure 12. With these safeguards,
the output can be held at voltages up to the VIN absolute
maximum rating.
BUCK CONVERTER WITH ADJUSTABLE SOFT-START
Large capacitive loads or high input voltages can cause
high input currents at start-up. Figure 13 shows a circuit
that limits the dv/dt of the output at start-up, controlling
the capacitor charge rate. The buck converter is a typical
configuration with the addition of R3, R4, CSS and Q1.
As the output starts to rise, Q1 turns on, regulating switch
current via the VC pin to maintain a constant dv/dt at the
output. Output rise time is controlled by the current through
CSS defined by R4 and Q1’s VBE. Once the output is in
regulation, Q1 turns off and the circuit operates normally.
R3 is transient protection for the base of Q1.
5V, 1A
REMOVABLE
INPUT
C2
0.33μF
CF
220pF
R3
54k
D1
10MQ060N
1766 F12
C3
2.2μF
RC
2.2k
CC
0.022μF
D3
10MQ060N
D2
1N4148W
L1
47μH
C1
100μF
10V
ALTERNATE
SUPPLY
R4
25k
R1
15.4k
R2
4.99k
BOOST
VIN
LT1766
SHDN
SYNC
SW
BIAS
FB
VC
GND
+
Figure 12. Dual Source Supply with 25μA Reverse Leakage
APPLICATIONS INFORMATION



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30


数据表 下载

Go To PDF Page


链接网址



ALLDATASHEET是否为您带来帮助?  [ DONATE ] 

关于 Alldatasheet   |   广告服务   |   联系我们   |   隐私政策   |   数据表链接    |   链接交换   |   制造商名单
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com